How to change the upholstery on chairs with your own hands: ideas, examples, photos

Damage and types of repair

Damage to a sofa or other upholstered furniture can vary in severity. Depending on the existing injuries, a different range of work is required. Here's what can happen to your furniture:

• Only the fabric became unusable (cats tore on the armrests, for example), i.e. There are no dips in the soft part or protruding parts. Then everything is more or less simple and you can get by by replacing the upholstery fabric.

  
  The simplest case is if you need to replace the fabric

• There are some dents in some places . This damage is caused by wear and tear on the components that make up the upholstered part of the sofa. Depending on the degree of damage and the design of the sofa itself, it may be necessary to replace padding polyester and other underlying layers. In more severe cases, repair of spring blocks, if any, or foam rubber/silicone if the sofa is spring is required. If the upholstery looks quite good, it can be washed and used again.
• Sink in the bottom of the seat . Sometimes, due to high loads, the springs pierce the bottom of the frame. This happens most often if it is made of fiberboard. In this case, you will have to disassemble everything, remove the spring dock, replace the fiberboard (preferably with plywood). This sufferer needs more than just replacement upholstery...
• Damage to the frame . One of the most unpleasant things is cracks in the frame bars. The sofa will have to be completely disassembled, the broken bars replaced, and then everything restored. This is a complete reupholstery of the sofa. Essentially, you're building a new one.

So reupholstering a sofa can involve different jobs. From simply replacing the upholstery to a complete renovation, including part of the frame. The most troublesome part is with the spring blocks. This is long and painstaking work. If the “historical accuracy” of your furniture is not important to you, it is easier to replace a failed spring block with foam rubber or (better, but more expensive) furniture silicone. If everything is done correctly, the sofa will become even more comfortable: incorrectly tightened springs cause a lot of inconvenience.

Types of structures, lifting mechanism

Roller blinds are classified according to the type of design control:

1. With chain mechanism. They are distinguished by the absence of guides and the ability to not limit the maximum length of the blade. In this case, the blinds hang freely; when lowered or raised, the canvas is pulled onto a special roller, to which a chain with a mechanism is attached.
2. With spring mechanism. In addition to the spring structure, they have guides along the edges and a special mechanism for fixing the material. They are conveniently located in the window opening, on its sash or in the doorway.

The classification by type of construction looks like this:

1. Classic. Blinds can hang freely or be placed inside a cassette; they can be attached to walls or ceilings.
2. Roller blinds. The size can be easily selected according to the dimensions of the sash. The design is cassette, equipped with guides.
3. Compact. These are mini curtains attached to a shaft with a chain that allows you to vary the amount of light entering the room.

Types of "soft part"

Let's talk in general terms about what the seat and back of the sofa can be made of. There are options:

• Without springs: High-density foam rubber (polyurethane foam, also called PU foam) (also called furniture rubber).
• Foamed latex. In terms of quality and convenience, it is better than foam rubber, but also much more expensive.

When restoring a sofa, you need to examine the layers.
These are the most common types of sofa seats. In more expensive models, the spring block can be supplemented with a layer of polyurethane foam or latex, which makes the seat more elastic and comfortable at the same time. When reupholstering, they then look at the condition of both parts, replace or leave them - depending on desire and capabilities.

The structure of sofa seats can be multi-layered

But that's not all the layers. In addition to springs, polyurethane foam/latex, padding polyester or thermal felt (or regular felt) are also laid. This is if the sofa is more or less modern and not too expensive. Older exhibits may contain matting or burlap, batting (or something very similar), horsehair, dried seaweed and other now almost exotic materials for sofa stuffing. When repairing a sofa, they will need to be replaced with the same ones (if you want to look) or similar in thickness and properties. So, to understand how a sofa should be reupholstered, first understand what’s inside it.

DIY pleated blinds

They are suitable for a living room located on the sunny side. These blinds look gentle and airy. Made from white Whatman paper, they will fit perfectly into any interior. Moreover, they can be made in any color scheme due to the possibility of painting them. The big advantage of such blinds is their low price (you can use suitable pieces of old wallpaper).

For paper blinds you need to prepare:

• Awl or hole punch.
• Wallpaper or sheet of whatman paper.
• Centimeter tape.
• Bead or cord retainer.
• Ruler 55−120 cm wide.
• Double-sided tape or other means of fastening.
• Scissors.
• Stationery knife.
• Cord or braid.
• A simple pencil.

Making blinds from wallpaper with your own hands begins with preparing the paper elements. Cut a piece from a roll of wallpaper, 30-40 centimeters longer than the height of the window. Line it from the wrong side into sections of 2-3 centimeters. Next, you need to apply a ruler and bend the strips, as for a fan. You can further seal the bend with a pencil. On vinyl wallpaper, it is allowed to make light cuts with a stationery knife.

eb48669b69880a60d67c42632cb6017d.jpe

Fold the accordion and make holes for the lace in the center of the strips using an awl or hole punch. You can make one hole in the center, which will subsequently result in a rounded bottom. If you use two cords, the blinds will be rectangular. It is better to use braid of the same diameter as the awl. Its length must be no less than the height of the window frame.

You can create the most unusual details with your own hands step by step. Curtains of this size will be able to be lowered completely in the future. To get a rounded bottom, you need to glue squares of Velcro tape to the corners. This procedure can be done using Moment glue or double-sided tape. An additional square for better fixation is located in the middle of the distance from the edge to the center.

A bead or clothes fastener is attached to the end of the lace so that it does not slip out when closing. The upper edge of the element must be attached either to the window with double-sided tape, or to an already installed cornice.

This design can be complemented with butterflies, sparkles and other decorative elements. The main thing when making and using such blinds is accuracy.

We disassemble the sofa and assess the scale of work

Reupholstering a sofa begins with disassembling it. During the process, you will be able to assess the extent of the damage and decide what exactly you need to do. For this part of the job you will need:

• a large screwdriver to unscrew visible bolts (if any);
• a small flat-head screwdriver, pliers or staple remover - to remove the staples that secure the upholstery.

The main thing is to remove the old upholstery.
Then everything will become clear. Actually, everything. First, remove the individual pillows, if any, and remove the side panels. It’s difficult to suggest here - there are many designs. Look carefully, you are sure to find something. If you have retractable parts, you can try starting with them.

Separating the upholstery

The next step is to separate the fabric from the frame. It is attached with staples to the wooden bars of the frame. We pry the staples with a flat screwdriver and pull them out. Some may fit very tightly; it is easier to pull them out by grabbing them by the raised back with pliers or pliers.

We disassemble the sofa: remove the staples

We remove the fabric carefully, trying not to damage it too much. We will then use it as a sample for new sofa upholstery. There are several layers underneath the upholstery fabric. Maybe felt, padding polyester, some kind of fabric. If the sofa repair was started only to replace the upholstery, look at the condition of these materials. If there are signs of wear, it is better to replace. After all, it will be a shame if in a few months the sofa needs to be reupholstered again, but this time because the layers of the lining have been removed.

If the sofa is old, there may be a picture like this

Once the fabric is removed, it's time to evaluate which parts you'll need to replace. Everything is clear with the upholstery and lining underneath. It is advisable to keep the pie in the same composition. If old materials were used that are not currently on sale or are too expensive, replace them with modern analogues. The main thing for folding sofas is to reach the same height of the seat and back that were before, since folding mechanisms are designed for certain parameters of the “pillows”. In order not to be mistaken with the thickness of materials, find unworn (or least worn) areas and measure the thickness.

Assessing the damage

This stage is needed if the sofa seat is uneven, there are humps and depressions, protruding springs (and from below too). In seats that consist only of foam rubber, everything is simple: they are usually replaced. They can be made from high-density foam rubber by folding several layers; you can order ready-made foam rubber at a store that sells furniture spare parts. It is wise to order a latex mattress according to exact dimensions (measure after removing the fabric and all layers).

If the sofa has springs, remove all the covering layers to get to them. If there are no burst springs, the frame and its connections are strong, without play or cracks, the backing for the springs is in good condition, you can stop there. We change the covering layers, sew a new cover, stretch it and fasten it. This completes the reupholstery of the sofa.

One of the common defects in spring blocks is a broken spring.

There are also such sofas - with spring snakes that are attached to the frame and give elasticity to the foam mattress standing on top

This type of sofa breakdown is also common: the fiberboard on the frame is broken

Inspect the spring block for broken springs

If there is any damage listed above, the spring unit will have to be separated. It is attached to the frame frame using U-shaped brackets or nails. Now you have completely disassembled your sofa into its components. Next is the replacement and repair of damaged parts, and then reassembly.

Roller blinds on the cornice

A more complex option to manufacture, but more convenient to use. Such roller blinds can be opened to any height, not manually, but using a counterweight system:

• Pockets are made at the top and bottom of the curtain, a curtain rod is installed in the top one, and the bottom one will be needed for weighting. In addition, two small plastic rings must be sewn on top (or embedded in the fabric), into which the cords will subsequently be threaded.

• On both sides of the window opening, two hooks are mounted on the wall; cords are attached to them, which are passed through the rings in the following order. The first is threaded through the bottom of the curtain and the top ring, the second is similar, only through both rings. The ends of the cords are collected (each on its own side) and secured to the hook.

Raising the curtains is carried out by tensioning the cord, which is fixed at the required degree of opening of the curtain on the same hook.

Classic sofa pie with a spring block and possible problems

To understand how to repair a sofa at home, you need to know what layers of materials are needed and in what order. For example, in a sofa seat with a spring block the sequence will be like this (from bottom to top):

1. Frame made of plywood or wooden blocks. A plywood frame is more reliable, but it takes longer and is more difficult to make. Therefore, pine bars are usually used. They are connected according to the tenon-groove principle, gluing the joint with wood glue. If desired, the connections can be strengthened with dowels or corners (aluminum).

   
   What layers should there be in a sofa seat?

2. Base for spring block . There may be options: lamellas (straps of elastic material), fiberboard, plywood. The most budget option is fiberboard, the most expensive is lamellas. The lamellas are attached to special stops (lamella holders). When using plastic stops, there is a risk of them breaking. At the same time, low-quality lamellas can bend (in normal condition they are curved slightly upward) or break - to reduce cost they are often placed at large intervals. All this leads to the fact that the sofa seat is pressed through. Instead of wooden slats, there may also be snake springs. They also have sufficient elasticity, but cost less. The problems with them are the same.
3. The spring block itself . The block can be with independent or dependent springs. The first one is cheaper, the second one supports the body well. Such mattresses are also called orthopedic.
4. Felt or thick fabric (teak or other similar dense fabric will do). This layer is needed so that the springs do not push through the foam rubber located above.

   
   This is what the slats look like from below

   
   If the fabric is thin, it will tear, then the foam will begin to crumble. But this is not the saddest thing - the lamellas were bent in the opposite direction. In normal condition they should be curved upwards

   
   Using a grosgrain ribbon allows you to redistribute the load

5. Polyurethane foam (PPU, foam rubber - all names of the same material). Special dense foam rubber is used. If you choose, in addition to density, look at such an indicator as the durability coefficient - the higher the number, the better (and more expensive). This indicator reflects how long the foam will take to restore its original shape after removing the load. Its thickness is taken according to the original, factory cake. You can make it thicker without restrictions only on upholstered furniture that does not fold out (banquette, sofa, armchair).
6. Sintepon . This is necessary so that the fabric does not “erase” the polyurethane foam. It is usually glued to a layer of foam rubber so that it does not bunch up during use. The glue is taken in a can.
7. Upholstery fabric . The best are tapestry, chenille. They don't fray and it's easy to sew with them. Flock and jacquard are good fabrics, but some of them “creep” at the seams. Therefore, when you sew, the seams need to be strengthened. By the way, it is better to sew upholstery for a sofa using special Tytan brand threads. Regular ones, even thick ones, will quickly tear.

These are all the layers and their features. You can add something (for example, a double layer of padding polyester), but removing it is highly undesirable.

How to choose fabric?

The choice of furniture surface material may be affected by the frequency of use of the sofa. So, if a piece of furniture is used by many people, and also by pets, then you should choose a material that is durable and does not get very dirty. In another case, you can purchase a simpler fabric so as not to overpay for those properties of the material that are not useful. Let's look at the main types of fabric that are suitable for upholstering a sofa:

Natural or artificial leather

Furniture with such a coating has a number of advantages: dust does not collect; moisture is not absorbed; hair and clothes are not electrified; durability and so on. In fact, this material is suitable for those who do not have pets or do, but they are trained and do not scratch furniture. Artificial leather or eco-leather is an excellent replacement for natural material. It is practically indistinguishable from the original and has all the properties of genuine leather. The artificial material can last up to 10 years, and when used, allergies will not occur in people suffering from this disease. Eco-leather is also pleasant to the touch and elastic.

Expert opinion

Sofia Kovalevskaya

Experienced housewife.

Ask me a question

You should not replace the upholstery with leather material yourself: leather has many nuances that an ordinary person cannot understand. It is better to seek the help of specialists who will make high-quality replacement leather.

Flocked fabric

This material is also not entirely suitable for pet owners, as it gets dirty quickly and may require frequent cleaning of the sofa. Hair will also accumulate on the surface. But such material is quite easy to clean with a brush and soap solution.

Textile fabric

It is universal: it cleans well, stretches and holds its shape, so it can be replaced by an inexperienced person.

Important ! It is worth carefully choosing the type of material and taking into account all the pros and cons, since you need to count on a long period of use so as not to often resort to repairs and waste of money.

The design of a sofa on snake springs and options for its restoration

Snake springs in expensive models are used as an additional means to increase elasticity. In budget models, a foam block can be placed on this base. They are attached to a wooden or metal frame across the seat - each spring separately. The installation step depends on the planned load. If your sofa begins to sag, or the springs have lost their elasticity or are broken, the solution is to replace them.

The spring, due to its elasticity, supports the materials on top

This is what it looks like disassembled

An expensive imported sofa is also made on a snake

To increase elasticity and extend service life, when reupholstering a sofa, the number of “snakes” can be increased. Another option is transverse reinforcement with rigid corsage ribbons (which are used for straps on bags and backpacks).

For durability and greater elasticity, use grosgrain ribbon

The tape is nailed on one side to the frame. Professional furniture makers then tighten it using a special tool, but it can be replaced with a regular block wrapped around the middle with coarse-grain sandpaper. You wrap a couple of turns of tape around this beam, pull with both hands (make sure that the frame does not bend), secure the tape with staples or nails, release and cut off the excess. The same method is also suitable for increasing the service life of a mattress with slats.

Differences between roller blinds and Roman blinds

Some people confuse roller blinds with Roman blinds, which are very similar in appearance, but have a different mechanism for lifting the curtains. Thus, when raised, Roman blinds are gathered into horizontal folds using a cord located on the sides or on the back. Roller blinds are wound onto a special rod, which is located at the top of the window opening. The web wound around the bar can be placed in plain sight or it can be hidden in a cassette.

Self-made roller blinds are rolled up at the bottom and secured with garter ribbons, which hang at a certain distance from each other along the width of the canvas.

An example of sofa repair with step-by-step photos

The old sofa became completely uncomfortable, began to sag in places and creak. There is no way to buy a new one, it was decided to reupholster and change the upholstery. As usual, reupholstering a sofa begins with disassembly. The legs were removed first. The railings were fastened with two large bolts; they were unscrewed and removed without any problems. Further disassembly is also not difficult - we unscrew the bolts that appear one by one.

Dismantling the sofa

When all the components were separated, the old upholstery was removed. The staples were easy to remove - the frame was made of pine timber. The spring block itself turned out to be without defects, but there was a crack in the frame, one of the frame beams sagged, the fiberboard sagged, although there were no cracks.

Frame repair

Since the frame bears the main load, it is better to replace damaged elements. We carefully measure them, draw them schematically, and put down the dimensions in millimeters. With the drawing we go to the carpentry shop. Please pay special attention: the wood must be dry, preferably kiln dried. If you know how to work with wood yourself, you can do it yourself.

Defects close up

It was decided to connect the frame, as it was, with a tenon/groove, coated with wood glue. But to prevent it from coming loose, the connection was reinforced with metal dowels.

Reassembling the frames

First, the connections are glued and clamped in a vice. A small diameter hole is drilled under the dowel and the dowel is hammered in. The frame stands in a vice until the glue dries.

We will use 4 mm thick plywood as the base for the spring block. The sheets are standard, a little more than 1.5 meters, and the length of the sofa is almost two. It turns out two pieces. It is better to make the joint of the pieces on a jumper, it is more reliable. We cut out rectangles of the required size, coat the frame with wood glue, lay plywood, and nail it with small nails. The length of the nails is so that they do not stick out outside the frame. We additionally support the joint with a plank (50*20 mm).

Let's start re-upholstering the sofa

The updated sofa will serve in the country house, so we try to keep the budget to a minimum; we use an old blanket instead of a backing for the springs. We stretch it well and fasten it with staples using a manual construction stapler.

The base for the springs is an old fleece blanket

If possible, it is advisable to put thermal felt here. It is more reliable and not so expensive. It is cut to size, straightened and nailed around the perimeter. You can use staples or nails with large heads.

Repairing and fixing the spring block

To fasten the spring block, you can use powerful U-shaped brackets, and it is better if their legs are sharpened. But the stapler does not work with these, so we cut staples from steel wire with a diameter of 1.5 mm and hammer them in with a hammer.

Updating the sofa at home: attaching a spring block

In addition to being attached to the frame, the springs are also secured with nylon straps. Twine was taken, folded in two layers, secured with the same wire staples. We tighten the constriction so that it does not press down on the springs, but the tension should be sufficient so that the block “does not move.”

Some dense material should be placed on top of the springs, usually felt. In this case, old flooring was used. Something like felt. It is quite dense and durable. Fold in two layers, cut to size. This layer must be attached to the spring block. The coating is dense, you can’t pierce it with a needle, even a gypsy one. A large diameter awl would be suitable, but there isn't one. We pierce the coating with a nail, which we push through with the handle of a screwdriver. We thread a thick thread into the holes made. The stitch pitch is about 3.5 cm. To speed up the process, we use several nails at once.

Upholstery of a sofa from scrap materials (budget upholstery of a sofa)

Next “according to plan” there should be foam rubber, on top of which a padding polyester is placed. In this project, it was replaced with two layers of densely elastic material, which had been stored in the attic for a long time. Instead of padding polyester, another old blanket was used. To prevent the blanket from moving around, it was grabbed around the perimeter with threads (in conventional technology, synthetic winterizer is glued to polyurethane foam or latex using glue from a can).

Case and cover

Upholstering this sofa turned out to be easy: the shape is simple, without decoration. The old cover was ripped open and a pattern was made from new, not very expensive upholstery fabric. In the place that falls on the corner of the sofa cushion/seat, a thick tape was sewn from the inside to prevent the fabric from fraying. The fabric is inexpensive, so the edges had to be rolled up to prevent fraying. They are often left unprocessed.

We put the finished part in the case

The finished cover was laid out on the floor, and the restored part of the sofa was placed in it. At this stage it is important that the fabric is stretched evenly and does not wrinkle. We started nailing the cover from the middle, moving towards the edges. Staples with thick backs were used to avoid damaging the fabric.

The sofa is almost finished

The back of the sofa was restored in the same way, the armrests were covered, then all the parts were screwed to the folding mechanism. The thickness of the pillows matched, so there were no problems.

The reupholstery of the sofa is finished. Result verified