DIY computer desk: 30 step-by-step instructions + photos

Many parents think about a workplace for their child. The decision to buy and assemble a computer desk needs to be approached quickly and thoroughly, especially if the future schoolchild is already growing up at home.

It will not be an extra saving for the family budget if you refuse to buy a workplace for the child, but think about how to assemble the table yourself. Moreover, if you approach the matter correctly, there will be no significant differences from furniture production in a specialized factory.

Common assembly errors

To assemble furniture with your own hands, you need to pay attention to some secrets and nuances that will help you avoid frequent and serious mistakes.
It is these annoying mistakes that can reduce the quality of the product, its service life, appearance, and sometimes even ruin the items. It is important to consider the following:

The first aspect that no instruction will tell you about, but which all assemblers know about, is working with an assistant. An extra pair of hands and eyes will never be superfluous; Often computer furniture is made of MDF. This is a soft material and is easy to damage

Therefore, instead of a drill, it is better to use an ordinary screwdriver; When installing the cabinet frame and drawers, it is important to check the corners. They must be strictly 90 degrees

Furniture should not be skewed. This is easy to check by level; the loops must be tightly “planted”; when attaching the back wall to the box, it is best to use self-tapping screws instead of nails; The computer desk has holes that are covered with plugs. These small parts are easily lost, so it is recommended to glue them to the surface; When using a screwdriver, you can accidentally scratch the furniture. If there is a protective film on the elements, it is better to remove it after finishing work.

Assembling computer furniture requires leisure. Strict adherence to the instructions and accuracy will help to carry out the installation work efficiently.

Use a screwdriver instead of a drill

Glue the plugs

Work with a partner

Required tools and fasteners

After opening the package, you need to disassemble the fasteners according to size. For small parts, it is best to designate a separate container. All elements should be compared with the quantities indicated in the diagram. The fastener kit may contain:

Screws;
Screws with nuts;
Fastening corners;
Wooden tenons for connecting parts;
Screwdriver keys.

It is important to take into account that the manufacturer already provides high-quality furniture with a full set of fasteners and holes. Otherwise, fasteners will have to be purchased separately.

To assemble the kit you will need:

Screwdriver;
Flathead and Phillips screwdrivers, preferably with a magnet that attracts nuts and screws;
Small hammer;
Pliers;
Ruler with corner;
Level;
Roulette;
Knife.

Assembling computer furniture is a process that requires care. To avoid damaging items, you need to follow simple rules.

Tools and Fasteners

Materials used

You can use different materials to make your own round table. This should include:

Chipboard and fibreboard are well suited to make a budget option. Despite the cheapness of this design, with proper care it will last a long time.

Using a tablecloth, you can hide the material used, and it will look no worse than a product made from natural wood.

Coniferous wood provides the opportunity to make a high-quality product at minimal cost. Such wood is easy to process and can last for a long time.

Solid wood in the form of oak or beech will allow you to make a truly high-quality product that will become the real pride of any room.

Such a table will have a decent appearance; it amazes with its massiveness and grandeur. You will have to try a little when processing this solid wood, but the result will not be long in coming.

This design emphasizes the status of the owner and his family members.

There really are a lot of options. There are also modern solutions to the issue using plastic.

What materials can it be made from?

A homemade computer table has a number of advantages over purchased furniture:

It can be corner, hinged or regular
Its dimensions will be ideal for the room
It can be made from any materials
This is environmentally friendly furniture
It's always nice to make it yourself

The cost of the product and its appearance depend on the material. The materials may be different: MDF sheets. This is a classic option.

You can choose any color of wood for the table.

The MDF material looks aesthetically pleasing and resembles wood. It is easy to process and reliable to use. MDF can replace other particle boards: chipboard or laminated chipboard.

Chipboard is one of the most popular materials for furniture.

Plywood. This material is the cheapest. However, it is the least reliable. Plywood is well suited for a country table.

Plywood is cheaper than wood, but less durable and strong.

Natural wood slabs. Solid wood furniture looks noble and luxurious. This is the most environmentally friendly material. However, it is very expensive. Another disadvantage is its heaviness.

Natural wood has been used to create furniture for many centuries.

How to assemble a corner computer desk with your own hands: drawings and diagrams

Do-it-yourself assembly of a homemade corner computer desk is practically no different from the option described above. The difference lies in the presence of 1 or 2 cabinets with drawers, an add-on for a monitor or documents, a large tabletop with a curved cutout opposite the user’s chair and a retractable keyboard board.

Main dimensions of a corner computer desk made of laminated chipboard

Drawings of a computer desk with dimensions and cutting of parts

The dimensions shown in the figure are approximate (except for the height and depth of the cabinets) and you can change them in accordance with your requirements and preferences. It is best to mill the tabletop and fill it with a plastic “T”-shaped edge. It will protect the ends from moisture and deformation. Also do the detailing as in the previous version with a straight table.

Sketch of a computer desk for PC with dimensions

How to assemble a computer corner desk: step-by-step instructions

The most difficult and dusty work is cutting, sanding and milling the tabletop. First, we mark the outline taking into account the width and depth of the cabinet with drawers and the stand for the “system unit”. We make a hole in the corner of the tabletop for the cable channel. We stuff a “T”-shaped or regular PVC edge with a thickness of 2 mm around the perimeter.

Marking a corner table top

Once the tabletop is completely ready, we can begin marking and drilling the remaining parts. It is better to immediately number the parts in accordance with the detailing - this will make it much easier to assemble the table. Next we proceed according to the following algorithm:

We assemble the drawers and install the halves of the guides on them.
Scheme for assembling drawers and installing guides
We assemble a cabinet for drawers, which consists of 2 sidewalls, a shelf, 4 ties (top and bottom) and a back wall made of fiberboard (filled last after installing the facades and connecting them into a single structure).
Dimensions for installation of roller guides
In the same way we assemble the section for the system unit.
We make a corner support post, which we connect with wide drawers to two already assembled functional blocks.
We attach furniture corners to the cabinets, supporting structure and drawers.
We install the table frame at the place of use, taking into account the necessary gaps and deviations. We attach the tabletop to the structure, mark the place where the planks with guides for the keyboard board are attached, and mount it to the inner surface.
We insert the drawers into the cabinet and check their movement. If the guides stick or knock, we check what the reason is; it may be a misalignment. We correct installation defects and if everything is fine, then we proceed to install the facades and countertops. Lastly, we fill the back wall of the cabinet with drawers.
We assemble the monitor stand and add-ons (if provided). That's it, the table is ready and you can start using it.

Monitor stand

Computer furniture assembly technology

First, you should lay out all the parts on the surface where the furniture will be assembled. This could be a floor covered with a protective film, or a special podium. It is recommended to clean the parts from dust. If we are talking about installing a computer desk, then it is more rational to start with a “box”, that is, assemble the bottom of the table (stand), side walls and tabletop. In this case, the structure will become stable. Before starting such work, it is important to check whether the frame will have guides along which the rollers of the drawers “slide”. Once the frame is ready, you can start working on the shelves and then move on to the drawers.

The technology for installing furniture frames comes down to two simple rules:

Without rigid fastening of the frame, the structure will fall apart like a house of cards. It is necessary to strictly fix the angles at 90 degrees;
Any horizontal surfaces about a meter long sag without supports. Therefore, partitions that support, for example, a tabletop, should be mounted together with the frame first.

Assembling computer furniture is not as complicated a process as it might seem at first glance. There will be no errors if you strictly follow the diagram and drawings.

Lay out the parts on the floor

Assembling the box and other large parts

We create a drawer for the computer or guides for it. We install the back wall. We assemble the drawers. We attach the guides, and the already assembled drawers to them. We mount the shelves.

Installing the keyboard stand Connecting all the large parts

Finding out goals and objectives

You set the parameters of your computer desk yourself.

Tables are different. Large, small, empty, filled with different shelf compartments. A successful choice will depend on how clear you are about your goals. For example, are you planning to use a laptop, desktop computer with all its components? What will you do at your workplace (write articles, program, do accounting, model, do video editing, etc.). There can be a lot of tasks. And based on your list of needs, you should make a thoughtful choice of computer desk. Let's say the choice falls on a desktop computer. Its components include a system unit, monitor, keyboard, mouse, speakers, modem, printer and various other additional devices. Based on this, calculate the required number of shelves. Another important point is the materials for making a computer desk. The most common inexpensive working material is chipboard. Of course, there are also expensive options.

https://housechief.ru/kompyuternyj-stol-svoimi-rukami.html
https://hozzi.ru/sovety/kak-sobrat-kompyuternyj-stol
https://novinkimebeli.ru/kompyuternyj-stol-svoimi-rukami/
https://berkem.ru/stoly/kak-sdelat-kompjuternyj-stol-svoimi-rukami/
https://mblx.ru/samostoyatelno/578-sborka-kompyuternoj-mebeli.html
https://mebelindesign.ru/sborka-stola/
https://thewalls.ru/mebel/razbiraem-poetapno-sborku-kompyuternogo-stola-svoimi-rukami.html

Comparison of appearance before and after

Now you should evaluate the result. We can say with full responsibility that everything turned out even better than initially expected. Although this is not surprising, because such work can never be planned in advance. During the process of altering or restoring furniture, something always changes, and therefore the result is usually completely unexpected, and sometimes even the opposite of what was intended. Well, you can evaluate the resulting computer desk in today’s example in comparison with what it was originally.

Choosing a tabletop

Before making a desk with your own hands, you also need to decide on the configuration of the tabletop. Products are:

Final word

Finding a new computer desk that fits perfectly into the color scheme of the interior is very difficult. And you shouldn’t spend extra money on it. It is much cheaper to restore an old table with your own hands. In this case, you can choose absolutely any color. You just need to use your imagination and hands. By the way, you can do the same with a computer desk purchased at a flea market for meager funds. In addition, remodeling furniture will not only relieve boredom during the work process, but will also give the room a completely new look and become the center of the interior. Well, the minimal cost of restoration will be a bonus to the work done, adding satisfaction from the work done.

We hope that the information presented today was interesting and useful to our dear reader. Any questions that arise while reading the article can be addressed in the discussions below. The Homius editors will definitely respond to each of them as quickly and comprehensively as possible. There you can leave your comment, share your impressions of what you read, or express your personal opinion on whether it is worth undertaking such a restoration or whether it is easier to purchase a new computer desk. Did you like today's article? Then don't forget to rate it. Every opinion is important to us.

Now almost every person has a tablet, laptop or personal computer. And if you can work with the first two devices even while lying on the couch, then this will not work with a PC. Therefore, for the convenience and health of users, it is recommended to work or play on a computer while sitting at a specially equipped table. Today's HouseChief editorial review is dedicated to how to make a computer desk with your own hands.

The designs of modern computer desks are striking in their diversity.

Read in the article

How to make a children's table with your own hands

A very simple option, with the help of these step-by-step photos you will learn how to easily make a children's table with your own hands. The dimensions are not indicated here, you can determine it yourself, let the child place his elbows on the table and reach his temples, the back should be straight. This will be the optimal height for your table.

If you want to approach the issue wisely, use the table. The manufacturing process is shown in some detail, so if you have the necessary tools it will not take much time.

Photo source www.woodgears.ca

How to make a children's table and chairs in pictures

Making your own children's table and chairs is not difficult if you have the appropriate tools and supplies. This article provides many examples with step-by-step photographs, but for greater clarity, I also present a master class with step-by-step pictures.

There is such a wonderful site WikiHow, here, like in comics, the process is depicted very colorfully.

Photo source www.wikihow.com/Make-a-Kids-Table-and-Chairs

Children's table with shelves

You can make such a table with shelves yourself, without particularly ruining the family budget. If your children love to draw and do crafts, shelves will be very useful. Therefore, the idea of building a table into a cabinet is very functional. How to make such a gift for children, look at the step-by-step photos with the indicated dimensions.

Photo source www.ana-white.com

Wood

Before you start making the structure, you should decide which wood to choose. Below is a table of comparative characteristics of different types of wood.

Tree type	Advantages	Flaws
Birch	strong material, does not crack or chip	For indoor use only, will not last long outdoors
Beech	light weight, can be processed manually	has a tendency to rot and requires additional processing
Oak	beautiful color, pattern, high hardness	expensive. Oak is difficult to work with due to its hardness
Spruce	has a beautiful texture	many knots require very painstaking processing. Even with a sander it is difficult to achieve a perfect surface
Maple	beautiful light shade, exquisite texture	To make the color last longer, treatment with special oil is required
Alder	light, durable, elastic, homogeneous mass	does not have a beautiful texture; wormholes are common in dry areas
Nut	beautiful texture, wide choice of colors, high hardness, reasonable price	Lightens with prolonged exposure to sunlight
Pine	easy to process, accepts impregnation and primer well	changes color over time, the wood rings become covered with a light coating

You should not focus solely on the hardness of the wood; this is not always the key to a high-quality and durable product. Universal structures are made from alder or spruce that can be used both indoors and outdoors.

In cases where price is a secondary issue, oak is usually chosen. If you need a budget option, use not wood, but chipboard or MDF.

How to make drawings of computer desks correctly

Of course, as a computer desk you can use a student’s desk or a standard office table, one of those that stood in offices 15-20 years ago. But taking into account the many additional devices, for example, a printer, MFP, and many gadgets that connect to the system unit or laptop, you will quickly understand that it is very difficult to fit into such a space for full-fledged work. In addition, the child will need to do his homework at the same table, that is, draw, read, write.

You need to make a table so that it has as much useful surface as possible, not occupied by equipment. And all devices - monitor, system unit, etc. - will be in their places, and at the same time will not interfere at all.

We will consider the option of a fully functional computer desk that you can make yourself without much expense.

First of all, you need to create a drawing that will take into account the dimensions of the entire structure. You can see a detailed drawing of the computer desk in the picture:

As you can see, this is the simplest, classic form of a table. Straight lines, conciseness, and at the same time full functionality. This table consists of a tabletop, a stand for the system unit, a retractable keyboard, cabinets and shelves.

Once you have decided on the required dimensions of your computer desk using the drawing, make a list of everything you need and start shopping.

Arrangement of useful table space

In order to make the shelves more convenient and practical, you need to do a little more work.

To arrange a useful space you will need:

shoe boxes;
ordinary cardboard;
self-adhesive film (about 2 m) and scrap paper with various patterns;
any thin glue;
hot glue gun with glue stick
scissors, stationery knife.

To begin with, narrow shelves are measured so that the manufactured organizers fit perfectly.

Decorating boxes with self-adhesive film and scrap paper

To begin with, shoe boxes are decorated with self-adhesive film. Its shade should contrast with the surface of the table. This will look much more interesting. After this, scrap paper is glued to the outer side. The print on it is selected individually

As for the lids, self-adhesive film is also placed on them. No patterns are needed on them; the surfaces will not be visible on the top shelf.

Such elements are suitable for storing various small items such as stickers, pens and pencils, headphones and wires, or other similar things. They look very good on the shelf.

Paper organizer and its manufacture

For the organizer, ordinary cardboard is used, from which parts are cut out to the required sizes. This is easy to do with the help of a ruler and a stationery knife.

Each of the parts is decorated according to the example of shoe boxes, after which hot-melt adhesive comes into play. The elements are connected, and the organizer can take its rightful place on a narrow shelf. Now there will be a place to put the documentation that should be at hand.

DIY photo of computer desks

Work progress

The assembly scheme for tables, regardless of the material from which they are made, is largely similar. Let's consider the algorithm of work using the example of a product made from boards.

We make a computer desk add-on

In order to make a full-fledged multifunctional computer desk, the instructions provide for not only a tabletop and shelves for additional devices, but also an add-on that will also perform a decorative function.

Mark and cut out the side elements of the structure, round the front upper sections with sandpaper. To ensure that the sides are evenly fixed to the tabletop, first make a template, the thickness of which will be 18 mm. Drill holes in its ends. Attach the manufactured ends to the tabletop and make markings for fasteners.
The marked holes should be drilled according to the following pattern: through holes - in the tabletop, blind holes - in the lower ends of the side walls. At this stage you will need a square, it will help you maintain the correct angles. Install the side pieces onto the tabletop using a square for alignment.
Screw in self-tapping screws under the tabletop, aligning the holes in the lid with the sockets in the ends of the sidewalls. After this, take a 400 X 2000 mm shield and cut it along the width. This way you will get a top shelf 315 mm wide and a securing cross-bar.
The middle vertical wall needs to be cut out of a panel measuring 200 X 2000 mm. Attach it to the tabletop in the same way as the large side walls, using a square to control the joints. Screw the back panel to the sides and place the top shelf on the end of the central wall. Align and fasten with self-tapping screws.
Now you need to make the left shelf. It will require a shield 200 mm wide. This shelf is intended for a printer or MFP, which means it must be strong enough and voluminous.

Circuit example

Instructions for assembling a computer desk may look like this:

The guides are marked and the box is assembled.
The walls must be connected to the stand and tabletop.
The next to be fixed are the false panels.
The back wall is attached to the box.
The side walls must be equipped with guides; drawers are subsequently placed on them.
The fittings and facade must be attached according to the diagram.
The tray for the system unit is assembled in the same way as the box.
If the structure has supports, they take their place on the tabletop.

The more detailed the content of the document, the easier and clearer the process itself will become.

The simplest table made from boards with your own hands: assembly with self-tapping screws

Let's analyze one of the easiest structures to work with: a rectangular table with four square legs, a drawer made of boards, without additional parts.

For a table measuring 80x120x70 cm you will need:

timber 40x40x680 mm, 4 pcs;
board 10...20x76 mm, 2 pcs. 650 mm long and 2 pcs. 1050 cm;
20mm board 1200mm long. Depending on the width of the board, the required quantity is selected to obtain a total tabletop width of 800 mm (8 pcs. 100 mm each, 4 pcs. 200 mm);
board for strengthening the corner joints of the drawer, section 20x75 mm, 4 pcs. length 100...200 mm;
wood screws 20...50 pcs.

Important: in this model, the parts are fastened using self-tapping screws screwed at an angle. To maintain a uniform angle for all drilled holes, it is convenient to use a simple device - a jig.

Assembly sequence:

After cutting the parts to size, the frame is assembled - drawer and legs. To do this, the parts are placed on a flat, smooth surface and temporarily secured with clamps (when working with an assistant, there is no such need). It is convenient to perform operations one by one - two drawers and a leg. It is necessary to maintain right angles between the drawers as accurately as possible. To connect the elements, drill holes at an angle and fasten the parts with self-tapping screws;

After assembling the frame, it is necessary to strengthen it in the corners. You can also use metal plates or, as already suggested, a board for this. If the second option is used, the edges of the board are cut at an angle of 45 degrees to fit tightly to the drawers, after which the board is screwed with self-tapping screws;

the prepared frame is checked for stability, and if necessary, the length of the legs is adjusted; arrange the tabletop by securing the boards to the frame

For this, as well as for attaching the legs to the drawers, self-tapping screws and holes drilled at an angle are used.

Important: the length of the screws is selected so that they do not go right through the tabletop! The completion of the work will be the treatment of wooden parts with varnish or paint.

Desk for a schoolchild with shelves

After we have chosen the desired design and material, we need to proceed to the construction stage. So, in the process of work we will need the following:

furniture panels in the amount of 2 pieces (pine) - dimensions 200x60x2.8 centimeters (length, width, thickness);
screwdriver;
rubber mallet (hammer);
drill with different drill bits;
fastenings;
wooden plugs (to cover furniture fastenings);
wooden dowels (we will use these to connect most of the parts);
wood glue;
level;
measuring tape or tape measure;
pencil.

It should be noted right away that we will not paint the wood with stain or other paint; in this case there will only be a varnish coating.

Video - Approximate calculation of desk parts

Step-by-step instruction

Step one: we will need to draw up a drawing that takes into account the dimensions of our room. It is necessary to display in the diagram all the dimensions of the parts that we will cut.

It is recommended to draw up a diagram of the future table in advance

Step two: Now we have to cut out the parts exactly according to the dimensions of the preliminary drawing. To do this, remove the packaging from the furniture panels, and then use a tape measure and a pencil to mark the cutting areas for future parts. Here you should be careful not to miss important points.

It is necessary to cut the parts using a circular saw or jigsaw. During the work, if necessary, we trim some parts

Of course, in this case, the obvious advantage will be the presence of special equipment, but in its absence, beginners can even use a bow saw in the process (they will just have to spend more time).

Step three: when all the parts are ready, we need to move on to the stage of assembling the structure. Since the parts of the table will be connected using wooden dowels, you will need to provide holes for them. They should be made on the end parts of the walls and legs of the structure using an electric drill.

It is necessary to insert furniture dowels into the prepared holes, coat them with glue, and hammer them in using a special rubber hammer

Step four: using dowels and a hammer, you should begin assembling the parts of the desk.

We connect the parts of the table legs together

Each part of the structure must be carefully sanded. After all, there should be no burrs left on the surface. The edges should be treated in the same way.

Parts processing

Step five: now we need to take the tabletop and hammer wooden dowels into the pre-prepared holes.

We hammer in the wooden dowels one by one. Now, using wood glue, we will connect the parts of the product to each other. Using a building level, it is better to make sure once again that the parts are positioned evenly, otherwise the table will turn out crooked. Using this principle, it is necessary to connect all parts of the table

Step six: now, using the remaining parts, we will need to assemble the shelves that will be at the bottom of the table.

First, you will need to arrange them in the sequence in which you are going to connect. If there are any irregularities, then it is at this stage that there will still be an opportunity to correct them.

Pre-assemble the structure

Using a compass, you need to mark the round corners, and then they can be cut out with a jigsaw. We make holes in the parts and connect them using glue and furniture dowels

European screws can be used as additional fastening elements to ensure the strength of the product. During the work, you will have to constantly use a building level to get a level structure.

During the assembly process, all parts will need to be sanded.

Particular attention should be paid to processing round corners.

As an additional decorative element, we installed chrome-plated steel tubes measuring 21 centimeters on each “floor” in such shelves. You will need to put plugs on each such tube. An exactly similar tube with plugs will be installed at the back of the table. But, this step is not mandatory - you can repeat it if desired.

Installation of chrome pipes

Step seven: now we just have to assemble the two parts of our table using wooden dowels and screws according to the markings.

Hammering the dowels

We mark the place of fastening of the top pipe and attach it to the table

Finally, we will need to sand all the edges of the table again so that they are perfectly smooth. In order to hide the places where the screws are attached, you should use special wooden plugs.

Final sanding

Step eight: now we need to varnish the table. It should be applied in several layers. It is important to remember that each layer must dry well for at least 2-3 hours.

Making the final coating

If desired, you can use either a roller or a brush (the first option is ideal for covering a tabletop).

Calculating the size of a computer desk

It is more difficult to calculate the dimensions for a corner computer desk, so we will first consider this option.

Corner table dimensions

Factors that influence the size of the table:

Tabletop width. The minimum tabletop width is 50 cm (500 mm). The optimal size is 60 cm (600 mm).
The width of the sections (which are the table supports). Each table has a different section width. If this is a processor tray – 20–25 cm (200–250 mm). If the tray has drawers or a door – 45–60 cm (450–600 mm).
Depth of the corner (where the person is located). The minimum size is 50 cm (500 mm), optimal is 60 cm (600 mm).

Common overlaps listed above -

tabletop width – 50 cm;
corner depth – 50 cm;
section width – 20 cm and 45 cm;
5 cm + 20 cm + 35.4 cm + 50 cm = 110.4 cm – the length of one table wing;
5 cm + 45 cm + 35.4 cm + 50 cm = 135.4 cm – the length of the second wing.

Optimal table size

tabletop width – 60 cm;
corner depth – 60 cm;
section width – 25 cm and 50 cm;
5 cm + 25 cm + 42.4 cm + 60 cm = 132.4 cm – the length of one table wing;
5 cm + 50 cm + 42.4 cm + 60 cm = 157.4 cm – the length of the second wing.

Optimal table size

with one tray: 5 cm + 5 cm + 25 cm + 60 cm = 95 cm;
with two trays: 5 cm + 5 cm + 25 cm + 50 cm + 60 cm = 145 cm.

Table height varies from 70 to 76 cm.

Note! It is not recommended to make the table higher or lower than the required dimensions, as this will lead to incorrect body position when working at the computer, the development and aggravation of back and spine diseases.

Drawing of a computer desk with dimensions

Where to begin

To understand how to assemble a two-door computer desk, you need to lay out all the available parts at the place where all stages of work will take place.

If the choice falls on a podium or table, things need to be covered with protective material; film is very suitable for this. Wipe parts thoroughly to remove dust and debris.

In order for the structure to be stable, assembly must begin with the box.

Important! Provide the frame with guides for the rollers on which the drawers are attached.

If there is a laptop in the house

We've discussed how to make a computer desk yourself. But what to do if there is a laptop in the house instead of a computer? It would seem that the thing is quite mobile and does not require additional stands. But, as practice shows, lying in bed or on the sofa with a laptop in your hands is not always comfortable. Therefore, now we will make a laptop table with our own hands.

The easiest and free option

First of all, let's consider a design that does not require special construction skills and not a penny of financial investment. It’s tempting to make such a table for a laptop with your own hands. You can use parts of old furniture, remnants from renovations and other scraps of any building material.

You only need three parts: 2 side parts and a table top. Its size will depend on the size of the equipment. We will make a tabletop 270x660 mm. It’s easy to cut, the main thing is to measure it exactly.

It will be a little more difficult with the side strips: they must have a beveled side, which is attached to the tabletop. The dimensions of the side walls are 270×205×255×280 mm. it turns out that the back of our table will be raised by 280 mm, and the front will be lowered by 205 mm. Thus, a small DIY computer desk for a laptop will have a slope, which will make it very convenient for work.

The side parts are attached to the tabletop using self-tapping screws and are additionally reinforced with small corners. This enhances the strength and reliability of the structure. All that remains is to paint or finish it to your taste and preference. There is nothing difficult in such a design, and if a person likes to study or have fun while reclining, then why not think about how to make a laptop table with your own hands.

Another way: a folding table for a laptop

The folding design of the table is a little more difficult to make, but if you often move from place to place, it’s worth thinking about how to make a laptop table convenient and mobile. The following materials and components will be required:

tabletop material;
side wall material;
screws or self-tapping screws;
4 folding fasteners with a lock.

You can use any material that is available. We cut out the tabletop 600x400 mm, the side legs - 400x310 mm. Using a ruler and pencil, mark the installation locations for the leg fasteners on the inside of the tabletop. We make holes for the screws, fasten everything securely and that’s it - our DIY computer desk, the photo of which you see, is ready.

As you can see, there are a lot of ways to make a computer desk with your own hands. The article discussed only the most accessible and simple ones. But there are craftsmen who are able to create furniture that you cannot find in any store.

Well, for clarity, watch the video on how to quickly and easily make a computer desk with your own hands, using the information from which you will cope with the problem easily and naturally.

Video:

What errors might there be?

When assembling furniture, you should not ignore the nuances and some tips; this will help eliminate gross mistakes. All mistakes made will certainly affect the quality and durability of the structure.

There is not a single word in the instructions that you need to enlist the help of at least one person.

Any owner who has encountered such an activity at least once in his life can tell how sometimes another pair of hands is missing. The assistant will definitely notice if something went wrong and will tell you about it.

Choosing a place

The table can occupy a corner of the room or stand along the wall.
The comfort of the room will depend on the correct location of the table. If the room is small, of course, it would be unreasonable to place a large table here. If the room can accommodate large furniture, a small computer desk may not seem like the most functional furniture option. It is worth focusing on the following aspects before placing furniture in the room:

A computer desk serves as a carrier for computer equipment, which naturally requires power supply

This means that it is important to place the table next to an outlet. It is advisable to work at the table during the consecration. There is no better light for work than daylight. Therefore, it is worth organizing the location of the table in such a way that the light from the windows falls on the left side of the computer area. Computer equipment on the table already obliges you to get rid of unnecessary heating objects in advance, which can cause a short circuit or fire. It is extremely unwise to place a table near a radiator, fireplace, or electric heater. It is recommended to free the occupied space from other various objects (paintings, shelves and decorative elements).

You can choose a hanging table model, which, if necessary, can be raised and free up space.

Tables are divided into several types: straight, corner and combined. Let's look at each option in order.

Even a simple table can look elegant.

Shelves can be either above or below the table.

Surface painting: some nuances

When applying acrylic paint, it is best to use a short-nap roller. A sponge as a fur coat is not the best option, although for lack of a better one, you can use it. The color is chosen depending on the preferences of the home craftsman. In today's example, we decided to use white for the base.

Most often it is necessary to apply 4-5 layers of paint for the base, although in each individual case it may be different. Everything will depend on the consistency of the paint. In this case, each layer must dry for at least two hours.

Combination table

This option is something between the first and second options. The design is functional and beautiful in design. But it takes up quite a lot of space. This is mainly due to the presence of various storage departments. The main role is played by cabinets, which allow you to hide things in such a way that they are always at hand and at the same time do not get in the way.

Straight table

The classic version of furniture is intended mainly for simple written work. The advantage of this type is good concentration on work and the ability to feel free. In this way, your attention is not wasted, and your productivity at work increases significantly. The stubborn table has its own requirements. If you have enough free space along the wall, then you will be comfortable working in your room.

Corner table

People who constantly work from home often have to sit in front of a computer screen. If you belong to this category of working employees, then a corner table is very suitable for you. Its advantages are that it requires little assembly materials and does not take up much space. This type of table is chosen by gamers.

The corner table also has its other side. According to psychologists, the angular design specifically puts pressure on the human psyche and provokes panic.

Finishing

The finished product is processed again with a grinding machine and a fine-grained abrasive belt P 150–P 280.

After grinding, begin polishing the surface. Then, if necessary, they are additionally treated with a primer and varnished. The varnish can be chosen in any color. If you decide to use paint, opt for alkyd or epoxy enamel.

We recommend reading:

Do-it-yourself upholstery (upholstery) of chairs: 100 photos of ready-made options and unusual designs
Do-it-yourself furniture decoupage: review of the best techniques, original ideas and beautiful design (140 photos)
How to update furniture with your own hands - a review of the best ideas for beautiful restoration of home furniture (120 photo ideas)

If you have minimal skills in working with wood, it is quite possible to make a table yourself. We are not talking about a complex transforming product, or a design with an adjustable tabletop height. But you are quite capable of making a beautiful and durable table with a simple design, following our recommendations. To make the work easier, below are photos of the table assembly.

Product type	Characteristic
Laminated chipboard	It is resistant to moisture, has a high degree of wear resistance, and cuts well. It can be cleaned with various household products. But despite its resistance to moisture, chipboard should not be exposed to it frequently, as the material may swell.
MDF	It can be used in children's rooms, as it is environmentally friendly, has a wide range of colors, is easy to process and durable. But if the surface is glossy, scratches will be clearly visible on it.
Tree	The most durable and durable material that matches any design style and is environmentally friendly. But a wooden tabletop is expensive, has quite a lot of weight and requires restoration after some time of use.