DIY kitchen corner: how to make, drawings, photos

Without a kitchen corner - a corner sofa in addition to a kitchen table and stools, chairs or bench - modern life is already unthinkable. Making a kitchen corner with your own hands makes sense not only for the sake of saving money: not every commercial model will definitely fit into a free corner of the kitchen, and the one that is suitable in size may not be suitable in design or price. A kitchen corner piece of furniture is not a complex piece of furniture, but a novice craftsman who is not properly equipped with rather expensive equipment will come across many pitfalls on the way to transform it into a product. This article is about how to bypass them and still make a corner in the kitchen at home that is not inferior to the factory one.

Note: the secret of the comfort that a kitchen corner creates is its aesthetic self-sufficiency. A corner sofa with a table and stools/bench is a self-zoning piece of furniture; it will create an area of calm and well-being, a kind of virtual bay window or alcove, even in an open field or barn.

Which one to do

It is possible to make a kitchen corner in different types of designs. The main requirements for a kitchen corner are compactness, convenience (ergonomics) and hygiene in the kitchen. We still need to achieve maximum savings in money, materials and labor by working as a public tool. Based on this, we will choose which one can be made simpler and better.

The main types of kitchen corners are shown in the photo. Pos. 1 – bay window corner, round or faceted. Each rider is allocated an optimal seat width of approx. at knee level. 400-450 mm. The bay window corner is extremely convenient and cozy, but, alas, it is complicated, expensive and requires an extensive kitchen.

Types of kitchen corners

A semi-bay window corner will fit into the kitchen of a modern apartment above the middle class: the side sections are straight, and the width of the corner at knee level is 200-300 mm, pos. 2. For a person of average build, sitting in the corner of a half-bay window is almost as comfortable as in a bay window. In a kitchen of normal dimensions, corners with a beveled corner are most often installed instead of half-bay windows; in them, the rider’s knees have 150-200 mm, pos. 3. You can’t move much anymore, but sitting quietly, no thoughts arise about where to put your knees.

Kitchenette with sleeping area

Lovers of small-sized kitchens most often make straight corners, pos. 4, with backrest wedge in the corner, pos. 5, and with a beveled back, pos. 5. Their convenience, technological complexity and cost are increasing in this series, but straight kitchen corners have a common positive property: if instead of a pair of stools on the long side of the kitchen table, the height of the bench is the same as the seats of the corner, then by moving the table and moving the bench, you can get a bed with a width of 600-850 mm. Very expensive and equipped with complex mechanisms, branded kitchen corners with a sleeping place are no more convenient, see fig. left. A corner with a beveled corner also has the property of transforming into a sleeping place without additional devices, if the corners of the seat of the complete bench are appropriate. beveled way.

Uncomfortable kitchen corner
Note: in fig. on the right is a perverse product of modern marketing - an expensive straight kitchen corner. In fact, the straight angle is the most uncomfortable of all. Much more inconvenient than its closest relative - a corner with a wedge in the back. A straight kitchen corner is only good for placing an unwanted guest in the corner. But he won’t be able to leave in English; he will have to push the owners away.

Corners with a beveled corner and a back are often complemented by a table and/or bar in the corner, pos. 7-9. The first two are not an option: getting something out from behind your back is inconvenient, but pushing it or accidentally knocking it over is easy. If the owners are firmly subject to prejudices and do not want to put anyone in a corner, then it is better to equip a mini-sideboard with a chest and a bar in the corner, as in pos. 9.

At pos. 6, 7 and 8 show corners with the so-called. hanging angle, i.e. without a separate support. Kitchen corners with hanging corners, made of laminated chipboard, are no less strong and durable than those with supporting corners, but they are cheaper and more technologically advanced to produce. However, they cannot be modular (see below), because initially performed only by the right or left. For the consumer, their cheapness is apparent, because... The hanging corner angle cannot be transported assembled and requires assembly on site.

Modular corners

Kitchen corners made from pieces of furniture that are not connected to each other (modular, see fig.) are good to produce and sell: there is no need to make right and left versions. They are also appreciated by those who often rearrange furniture; modular kitchen corners look good in studio apartments of laconic styles, such as loft, high-tech, minimalism. But the functionality and ergonomics of modular kitchen corners, simply put, are non-existent - you can’t put anything in them, and it’s uncomfortable to sit in the corner.

Modular kitchen corners

Note: traditional kitchen corners are also made modular, consisting of 3 separate items - a pair of sofas and a corner. They are placed right or left, turning the corner by 90 degrees, and one of the sofas by 180. However, such corners are more expensive, because Extra material is required for the corner and its design becomes more complicated. It is very difficult to make a modular kitchen corner at home, because... To the required accuracy of pairing of parts within 1 item (see below), the accuracy of pairing of objects with each other is added.

Decorating the finished corner

Decoration options are selected to suit the interior style and personal preferences of the apartment owners. It is for this reason that the design options are unlimited. Let's look at the most popular of them.

Natural wood will always look great in any kitchen. If all the kitchen furniture is made of a similar material, then the design should focus on this option. Natural wood is safe, environmentally friendly, and looks very status and dignified, and also brings warmth and comfort to the space. Natural wood can be coated with tinting or varnish.
If upholstery is not provided for the sofa, then you can cover the surface using paint to match the color of the rest of the kitchen furniture or some decorative element. A combination of two or three harmonious colors always looks aesthetically pleasing and harmonious.
A relevant option is to decorate the kitchen corner with plastic or other similar modern materials. Such options wash well, retain their original appearance for a long time, and the choice of colors and shades is not at all limited. However, such material will not fit into every style. It would be more appropriate to use it in modern interiors: hi-tech, minimalism, and so on.

The material of the third millennium is microfiber. This material is very wear-resistant, it does not lose color and is easy to clean from dirt. Microfiber is made from polyester or cotton fibers.

What to do and what not to do

The first mistake when designing a kitchen corner is a table with legs and straight front seats, pos. 1 in Fig. The secret of the comfort and self-zoning of a kitchen corner is its compactness and convenience, but here the table cannot be really moved, and its legs get tangled in the knees of 3 people sitting. The corner for the kitchen should be made under the table of a beam-and-panel structure, pos. 2 and 3, and the facades of the seats are either sloping (pos. 2) or with raised bottoms of the chests under the seats, pos. 3.

Tables and drawers for kitchen corners

The second mistake is not to make drawers under the seats, pos. 4 and 5. They interfere with each other and spoil the floor. To get to the contents of the drawers, you need to move the table far away and kneel down. If the house is run by a maid and a housekeeper, and the owner does not care about their worries, then a kitchen corner with drawers is a matter of taste. And we need to make a corner for ourselves in the kitchen with chests under folding or removable seats.

Silent history

The ancestors of small-sized kitchen corners are corner sofas, which appeared in the postmodern era and firmly entered into fashion as an indispensable piece of furniture for saving space and being easy to use.

A little later, in Europe and the USA, small canapés and sofas for kitchens began to be sold, eventually improved to accommodate corners. And soon similar products appear in the post-Soviet space - far from the trends of exquisite design. For example, if in the West the corners were already decorated in the Art Nouveau style, and the material for their assembly was natural wood, then in our country it was chipboard, painted and upholstered in red fabric (

Get to work!

Which corner of your kitchen is best suited is up to you. And here we will see what difficulties you will encounter when making it at home without experience, and how to cope with them. The analysis will be based on the example of a design known in RuNet, the drawings of which are given below; The main materials are laminated and simple sanded chipboard with a thickness of 16 mm.

Drawings of a kitchen corner made of laminated chipboard

Specification for kitchen corner drawings

On the one hand, this corner requires minimal materials and labor and can be made much more convenient, see below. On the other hand, the prototype is oriented towards industrial technology, its design is rational and well-developed, but we need to get a product no worse than that, assembling it at home on the knee and in weight. This particular sample was also chosen because it is capable of acquiring all the best qualities of a corner with a beveled corner, plus the ability to serve as a sleeping place, but technologically it is not much more complicated than a right corner. In addition, there is a generally correct specification for it with statements of material and fittings, see fig. on right.

Note: if you check/refer to other sources with descriptions of this sample, keep in mind that in some of them, and quite a few, in the drawings of the parts the dimensions are given mixed for sofas with a length of 100 and 60 cm. Assemble the blanks cut out from them into the product, of course, impossible.

For example, in the top row of Fig. Assembly diagrams are provided with the drawings, clear as day to a factory technologist. But what to do with them if you don’t have production equipment? The sample under consideration is a panel box-shaped structure, similar to the power circuit with load-bearing skin in the aircraft industry. Box-panel structures save material and labor as much as possible, resulting in very durable products, but their manufacturing technology is subject to a number of specific requirements. There are a lot of invisible tricks here, but we can deal with them, and we will do it. First for the sofas, in this order:

Selection of fasteners;
Adjusting dimensions for a specific room;
Cutting laminated chipboard and chipboard into blanks, marking and drilling holes;
Trimming the edges of beveled parts and edging;
Covering the parts for which it is required with soft covering;
Assembly.

Next, let's see how we can simplify the manufacture of a corner section (corner) and make it more convenient. The original design is modular, but in our apartment the corners of the walls do not change places by themselves. Knowing exactly where the corner will go, whether it will be right or left, the corner can be made hanging (see below), and this will make the work much easier and cheaper.

Fasteners

The main fastening elements of this kitchen corner that absorb operational loads are confirmed furniture screws and steel corner connectors; dowels play a supporting role, keeping the parts from moving. The specification above contains a list of accessories for assembly in an industrial environment, but for home use, some things will have to be changed in it.

Note: in products made from laminated chipboard and chipboard, it is possible to replace confirmats with wood screws to connect parts through the face into the edge occasionally. In this product - under no circumstances is it possible, because... the boards are very thin, 16 mm. The connecting corners are attached to the parts using wood screws, see below.

Confirmations

The standard size of confirmats 7x50 specified in the specification is the maximum permissible for a given chipboard/laminated chipboard thickness. This makes it possible to transport the corner modules in assembled form and reduce its cost somewhat, because there is no need for on-site assembly, and any of the modules is carried into the apartment by hand by a person with the physical development of an office type. But marking and drilling for the thickest possible fasteners also requires production precision (see below), which cannot be achieved by working at home with your hands. For example, can you, when working with a hand-held electric drill, feed the drill perpendicularly or parallel to the face of the board with a deviation to the side of no more than 0.1 mm? The question is rhetorical. Therefore, for manual work, provided that the product will not be transported over long distances with shaking and jolts, the size of the confirmats should be reduced to 6x50 or even 5x60. Otherwise, i.e. If you take fasteners according to industrial specifications, some of the parts may delaminate during drilling or assembly. If the chipboard/chipboard is taken from eco-friendly brands E0 or E1, then it will definitely delaminate, so the chipboard/chipboard should be taken from the household brand E2, and if you want E0/E1, then the thickness of the boards needs to be increased to 24/20 mm, adjusting accordingly. dimensions, see below.

Fasteners and connecting elements for the kitchen corner

The height of the screw neck H is important for the strength of the confirmed connection, see pos. 1 in Fig. H must be exactly equal to the thickness of the overlay board, on the right in pos. 1. Sometimes H is indicated by the 3rd digit in the name of the screw size, i.e. you will need confirmations 6x50x16 or 5x60x16 for the original structure or 6x50x24/6x50x20 or 5x60x24/5x60x20 in the case of using boards of greater thickness.

The confirmation drill must be taken exactly for the given screw size. The height of its skirt should be equal to H (in the center in position 1), the diameter should be equal to the diameter of the screw body without thread, and the length of the spiral part of the drill L (without cutting tip) should be equal to the full length of the threaded part of the screw. If the heel of the screw rests on the residual conical hole in the hole, then hidden delamination in thin boards is guaranteed, and it is only a matter of time before it spreads outward. Small.

Dowels

In all sources on the topic of the kitchen corner in question, photos of wooden dowels are given as illustrations with enviable consistency, but without proper understanding. This is a gross mistake in this case. Wooden dowels are designed for connecting wooden parts: they dry out along with the base material, and the connection remains strong for many years. Or centuries, if the furniture was made by an outstanding master.

Chipboard/chipboard do not dry out and are therefore connected with plastic dowels. If you take slightly more expensive propylene ones, then there is no need for rather labor-intensive and careful gluing of joints. For the reasons stated above, the diameter of dowels for manual production must be reduced to 6 mm, leaving their length the same. In the edges of the boards, holes for dowels are drilled only along the jig (item 4 in the figure); diameter - 5.3 mm, drilling depth 22 mm in the edges and 12 mm in the faces.

The seats (see below) can be made not folding, but removable, by placing them on dowels with round heads for detachable connections (above, position 2). This will allow you to avoid the rather complex installation of piano hinges, the costs of them and fasteners for them. And if they decide to rearrange the corner in a hurry, then the likelihood of damage to it is reduced: they grabbed the seat without thinking, it remained in their hands, and the sofa did not jump or hit anything. Getting something out of the chest under the seat on piano hinges is no more convenient, because... The seat cover reclines less than 90 degrees. It’s easier to remove it and lean it against the back than to rummage through the chest while holding the lid with your hand. But in the design under consideration this, unfortunately, is impossible, see below.

It is better to take other dowels for our kitchen corner with faceplates, at the bottom at pos. 2. Washer thickness 0.5-0.7 mm; At first such gaps will not be visible. After some time, the washers will be pressed into the chipboard (the parts are tightly tightened with confirmats), the gaps will converge, and the entire product will acquire additional strength. Another advantage of dowels of this type is different corrugations on the long and short parts, which provides even higher strength of the connection without the danger of delamination of the boards. You just need to select dowels of the required size: with a 20 mm long part and a 10 mm short part (for 16 mm boards). For boards 20/24 mm, the long part needs 30 mm, and the short part 12/16 mm.

Corners

For the design in question, you will need steel isosceles corner connectors 30x20x2 (for fastening obliquely) or 30x15x2 for fastening in a row. The first number indicates the length of the corner shelves, the second their width, the third – the thickness of the material. During assembly, the corners will have to be partially bent to install inclined parts, so you need to take them white or gray from viscous “raw” or moderately annealed steel. The presence of stiffness stamping on the bend for bent corners is unacceptable, pos. 4 in Fig. The internal and external folds of the corners should be smooth, without tears or wrinkles. The corners of burnt steel, yellowish with spots of tarnish, even if they bend, will then crack. Black phosphated corners from the so-called. Overdried steel is very strong, but when bent, it breaks immediately.

Note: just so you know, plastic furniture corners can be bent by thoroughly heating them with a household hairdryer at full power. But plastic corners last no more than 3-5 years, and then they dry out and crack.

Dimensions

Let's look again at Fig. with drawings (duplicated on the right). The dimensions have been corrected: the length of a sofa 1 m long is shown in black; red and blue next to the “black” ones for a small sofa 60 cm long. The green marks will come in handy later when we get to the corner seat.

The “red” dimensions are basic: you need to add to them the missing amount of 600 mm for longer sofas. For example, for a sofa 1.3 m long, you need to add 700 mm to the “red” dimensions. The longest possible length of a sofa of this design is 1.5 m. “Blue” dimensions are relevant for sofas up to 750 mm long. If the sofa is longer, you need to take “black” sizes instead of “blue” ones.

6th position

There is no 6th part in the drawings. This is a seat blank, a simple board without any holes. Its length is equal to the length of the lengths of the sofa (968/568 mm in the drawings) minus the double thickness of the upholstery fabric, it is kept within 1-3 mm. The thickness of the optimal flock and microfiber in the kitchen is approx. 1.5 mm taking into account folds, so in this version the seat length will be 965 mm for a large sofa and 565 mm for a small one. Minimum seat width 297 mm, including fabric upholstery and installation on piano hinges, see below. If the dimensions of the kitchen allow, the width of the seat can be increased, then an overhang will form in front. With the corner seat option discussed below, the maximum width of the sofa seats is 444 mm; then the seat bevel of the corner section is reduced. In this case, the width of the bed can be up to 900 mm.

Cutting and Sawing

Sawing chipboard/laminated chipboard sheets into parts is done using a jigsaw along the contour. The contour is drawn according to the template, so the jigsaw file must be guided along the inner edge of its line. The upper and lower edges of parts 2 (chest front) and 8 (back base) in Fig. with the drawings you need to cut it obliquely, for which you need a jigsaw with a tilting shoe or you will need to buy a shoe for the existing one. The angle of inclination of the front of the chest is 10 degrees, and the back is 5 degrees. Some shoe scales are graduated in units of relative inclination; for an angle of 5 degrees it is 0.085, and for 10 degrees it is 0.177. Not 0.175, as it might seem, since the relative slope is nothing more than the tangent resp. corner.

The jigsaw file for trimming is beveled inward from the edge to be trimmed. For children 2 (facade), the upper edge is cut from the face so that the upper outer corner remains intact, and the lower edge, on the contrary, from the underside (wrong side), so as not to cut off the inner lower corner. The edges of the backrest, because it is tilted back to the facade, cut in the reverse order: the top one from the back, and the bottom one from the front.

Edging

The free edges of the kitchen corner parts need to be covered with something that matches the overall tone. Edging PVC kitchen furniture with a T-shaped edge is undesirable, not because the groove for the edge needs to be selected with a milling machine, but because dirt will accumulate in the gaps of the edge. By the way, for the same reason, it is advisable to make a kitchen table under a ready-made postforming tabletop: it does not require edging at all and is equipped with a drip tray.

The visible and touchable edges of kitchen furniture are covered with a tape made of complex ABS plastic (ABS, acrylonitrite butadiene styrene) up to 2 mm thick, and the back ones and those above the floor are covered with crepe paper tape. ABS is absolutely safe, hygienic and environmentally friendly; medical equipment is also made from it. ABS and paper edges are produced dry and self-adhesive. The first ones are intended for industrial use with a separate supply of glue, so you need to get self-adhesive ones. Edging a kitchen corner with self-adhesive edges is done as follows:

The edge strip is cut from the roll to the required length plus 2-3 cm. It is convenient to measure the lengths of curved edges with a tailor's meter.
Peel off 2-4 cm of protective film from the end of the segment without touching the adhesive layer with your fingers.
Place the end of the tape on the edge exactly lengthwise and press.
Holding the tape with your hand, with the other hand you pull out the protective film from under it by the original “tail”. The tape should lie on the edge itself.
When the tape is all on the edge, it is rolled with a rubber roller.

In general, the procedure is the same as for high-quality self-adhesive gluing. By the way, this is a good finishing option if you decide to make the entire kitchen corner from inexpensive sanded chipboard: there are few visible parts in it, and the textured self-adhesive under acrylic varnish from natural wood will not be immediately distinguishable even by an experienced carpenter. Self-adhesive gluing is done after sawing and trimming the edges before edging. In this case, the inside of the chest can simply be varnished.

Marking and drilling

The accuracy of marking parts of box-panel structures made of chipboard/laminated chipboard is required to be no worse than +/-0.5 mm, but how can it be maintained on edges and sanded chipboard if the size of the material fibers is of the same order? There are no problems with this at the factory; there are no markings as such - they cut and drill using automatic machines. In handicraft production, they use templates, but in order to check each one, you have to ruin up to 2-3 blanks. For piece production at home, this is unacceptable, if only because you need a lot of templates and so much time is required to make them that it is easier to buy a ready-made corner. Moreover, the quality of the product made from parts marked according to templates turns out to be 3+ at best.

Marking calipers

Firstly, the marking of holes on the parts of the kitchen corner made of chipboard/laminated chipboard should be done so-called. a marking caliper with sharp jaws for measuring external dimensions and a vernier for precise installation of the carriage (on the left in the figure). Experienced mechanics sometimes make a marking caliper from a regular one, sharply and very carefully sharpening the tightly knit outer jaws on fine sandpaper, but manually align the tool carriage exactly according to Vernier is difficult.

Note: electronic booms, incl. The marking ones (on the right in the figure) are actually not so convenient to use, and the marking accuracy is worse. Here electronics have not yet caught up with good old mechanics.

Next, marking the holes on all parts is done from the bottom. When marking asymmetrical sidewalls, keep this in mind so that it does not turn out to be a mirror image. The right and left sidewalls are, of course, mirror marked.

Then, between the centers of the outer holes for fastening the mating part, axial lines are drawn into the edge with confirmations and beaten from them to the sides along half the width of the attached board. The extension of the attached part is marked along the center line and is also marked to form the contour of its edge. On the bottom of each board, you need to mark the contours of all attached edges in this way, this is necessary for accurate assembly. The accuracy of beating edges is required +/-0.5 mm, which in this case is ensured by a fitter's angle with millimeter divisions and a steel fitter's ruler.

Sverlovka

Drilling of blind holes for dowels is carried out immediately along the required diameter to the required depth, as described above. But for now we drill holes for confirmations only through the faces of the boards and only with the spiral part of the drill, i.e. not to full diameter. We will drill it completely later, in the order of assembly, so the entire kitchen corner will turn out without distortions and cracks.

Required Tools

So that during the assembly process you do not have to be distracted by searching for the right item or material, you need to take care in advance of what may be needed for manufacturing. The master will need:

hammer;
jigsaw;
drill or screwdriver;
roulette;
accessories;
stapler;
glue;
sewing machine;
stationery knife;
anti-stapler.

Classification of kitchen cabinets, characteristics of the main varieties
The last tool is optional. With its help, it will be easier to remove failed areas of the upholstery, if there are any, but you can also do without it, which cannot be said about everything else. When assembling a kitchen corner, this minimum of tools is required.

Upholstery and upholstery

Before assembly, the sofas need to have their backrests and seats completely covered, and the corner seat parts also require backrest segments separately. We will talk about covering and assembling the corner of the kitchen corner later, but for now we will limit ourselves to sofas.

Holofiber, which is excellent for interior furniture, does not fit well in the kitchen; in the local microclimate it is not particularly hygienic. The soft padding of kitchen furniture is made from low-permeability foam rubber of the EL2240, EL2540, EL2842, EL3050, EL3245, EL3550 and EL4050 brands. The first 2 digits characterize the hardness, and the last 2 indicate the density in kg/cubic meter. m. The load-bearing capacity within this range increases from 60 to 120 kg per square meter. m, this means that this material is able to withstand such weight indefinitely, completely straightening when the load is removed. Foam rubber EL2842 is universal; lower brands go to the backrest, EL3050 and EL3245 to the seat, and EL3550 and EL4050 are intended for furniture in public buildings or for particularly heavy riders.

The thickness of the foam layer is 20-40 mm. It is recommended to cut this evenly with a heated nichrome thread. It’s also not difficult to make a machine for cutting polystyrene and foam rubber with your own hands, but it’s still extra work. In addition, for the machine to be safe, the thread must be powered from a 12V 5A power source, and this is more serious work or a significant waste of money. However, cutting pieces of foam rubber with fairly even edges can be simpler:

A steel bench ruler is taped along the cutting line;
The cut is carried out with a new, absolutely sharp mounting knife in several steps along a ruler;
For the first cut, the blade is extended 5-7 mm, and the knife clip rests on the ruler. Take a closer look at your knife - the end of its clip is at an angle, this is just for such cases;
For subsequent cuts, the blade is advanced further by the same amount until the entire layer is cut.

Covering the kitchen corner seat with foam

The seats of the kitchen corner are covered with foam rubber with a fold along the front edge. For the hem you need to give an allowance of 2-3 times the thickness of the board. Sheets of foam rubber for the backs are cut exactly to the size of the base. The foam rubber is glued with 88-grade glue, the folds are glued last. If the seat has a stem, then before gluing it is better to round its front edge, and give the foam allowance equal to 4-5 times the thickness of the board, see fig. on right. It will be much more comfortable to sit on such a seat.

tight fitting

Conventional upholstery fabrics are rarely used in high-quality kitchen furniture, because... quickly become saturated with fumes and get dirty. Leatherette is more hygienic, but sitting on it in the heat is unpleasant, and installing air conditioning in the kitchen is not advisable for many reasons. It is best to cover the kitchen corner with flock or microfiber.

Flock is available in plain and colored, smooth and embossed, on the left and in the center in Fig. Dirt becomes entangled in its fibers without migrating back, and is removed during mandatory regular cleaning at least once every 2-3 months. Flock upholstery of kitchen furniture lasts up to 10 years or more.

Covering the kitchen corner with flock and microfiber

Microfiber works on the same principle, but its fibers are regular plexuses of the finest fibers. Microfiber seems to draw dirt into itself and hold it firmly; This material was originally developed for cleaning optical glasses. Microfiber is available only in single-color, modest colors (on the right in the figure); does not require maintenance at all times of use. Unfortunately, this material is expensive and lasts no more than 3-5 years, and then you need to completely change the upholstery: microfiber cannot be cleaned, because... in this case, its structure is disrupted.

Fasten the flock and microfiber upholstery as usual, using a furniture stapler to the underside of the base. The folds at the corners are glued with 88-grade glue: the fold is turned away, glue is dripped onto the fabric adjacent to the base, left until tack-free, and the folded fold is pressed. There is no need to glue PVA, it can cause stains visible from the outside.

Assembly

Assembling furniture using corner clamps

Before final assembly, thrust bearings are placed on the legs of the sidewalls. Any board as wide as thick will do, but it’s still better to use round ones with threaded or dowel heads instead of those recommended by the authors of the original design: there will be fewer nooks and crannies for dirt to accumulate. Dowel bearings are cheaper than threaded ones, and they are easier to install: holes are drilled in the edge of the leg for dowels (6 mm in this case), and the bearings are simply pushed into place.

How to assemble homemade box-panel furniture without distortions, cracks and without using complex production equipment, this is, as they say, another question. In this case, you cannot do without a pair of corner furniture clamps, see fig. on right. Welding corner clamps with a common clamp are not suitable, they cannot accurately bring together the parts to be connected, but with the help of furniture clamps this is not so difficult:

They put dowels in the children. 4 in the drawing, lightly tapping with a rubber hammer or mallet;
One of the sidewalls (part 1 in the drawing) and the back wall of the chest (part 4) are tightened with clamps so that the edge of the part. 4 entered the contour marked for her on the underside of the child. 1;
Drill holes for confirmations and screw them in;
Without removing the clamps, they place the children on the dowels. 3 – bottom of the chest;
The upper clamp is removed and moved to the far corner of parts 3 and 4;
Connect parts 3 and 4 (with additional drilling of holes for confirmations). The clamp from their corner is immediately removed, otherwise it will remain in the sofa;
Remove the remaining clamp (don’t forget!), put the child. 5 (lower backrest brace) and attach to det. 4;
They put children. 2 – façade of the stall;
Attach the second side panel without screwing the confirms all the way. You just need to bait so that the dowel heads fit slightly into the holes;
Assemble the backrest (inset at the bottom right in the figure with drawings) and put it in place, then pushing the sides of the backrest apart. The confirmations on the 2nd side are holding up;
The seat is hung on piano hinges, see below.

Here a possible question may arise: why use clamps if there are already dowels? The dowels are not guides, they do not hold the angle and can break during hanging. Taking into account the fact that marking and sawing were done by hand, it was impossible to do without clamps. Conscientious professional furniture assemblers use clamps with all their might, but why do we need to hack around for ourselves?

Seats

In our case, it will not be possible to place the seats on dowels with rounded heads, because The façade of the stall is slanted. If you limit yourself to dowels on the edge of its rear wall, they will quickly break out even if you carefully remove the seat cover. The seats of the sofas in the kitchen corner are hung on piano hinges, but it’s not worth taking 1-2 long ones (item 1 in the figure): it’s difficult to hang the lid of the chest on these so that it lies in place evenly and does not warp when folded back, without special equipment. You need to take 3-4 short loops for fastening in a row, pos. 2. Loops for fastening with a zigzag (item 3) are not suitable - how to attach them to a 16 mm board? The same applies to card loops, pos. 4, strongly recommended by a number of authors.

Hinges for hanging kitchen corner seats

The wings of the seat hinges should be as wide as the thickness of the board. First, the hinges are placed on the seat, aligning the edges of the wings along the bottom edge of the board along with the upholstery. Then an assistant is needed: he will hold the seat, and the master will align the edge of the wing of one of the outer hinges with the lower edge of the board of the lower backrest screed (detail 5 in the drawings) and attach a pair of screws, not reaching them all the way. Then the other outermost loop is attached in the same way, and after that the rest are fastened to full tension and the outermost ones are pulled out. The assistant keeps the seat reclined all this time.

Professional advice for direct kitchens

We save space: a kitchen corner for a small kitchen, photo, manufacturing technology
The optimal length of a linear kitchen is 2.5 m.

A direct kitchen project always begins with a sink, since the pipes are already installed. Traditionally, the sink is in the corner, so for the convenience of your hands you need to step back 0.5 m from the wall, especially if the sink is located on the right, your right elbow will constantly hit the wall.

If the length of the set is less than 2.5 m, you can move the sink between the stove and the refrigerator. With a long kitchen it will be difficult to redo the communications; a pump is needed.

The washing machine or dishwasher should be closer to the sink. The drain will work much more efficiently if the water drain is close. You won't have to carry dirty dishes far.

In a narrow kitchen, it is more practical to have deeper cabinets on the lower tier (at least 60 cm). If there is less than 1 m between the furniture and the dining table or wall, it will seem very cramped.

If the refrigerator is located near the stove, then a gap of more than 15 cm is required. Especially if it is a gas stove, the side of the refrigerator should not heat up and suffer from constant splashes of grease.

In a long kitchen, it is better to have cabinets up to the ceiling; they hide a refrigerator, microwave oven, etc. To add volume to the room, it is better to buy a straight white kitchen. Cabinets up to the ceiling are comfortable and fit well into a kitchen-studio or kitchen-hall.

When ordering a kitchen, it is better to replace wall shelves 0.7 m high with 0.9 m. The space for kitchen needs will increase, long cabinets will visually raise the ceilings. Another interesting option is to hang cabinets in 2 rows.

To increase the area of a small kitchen, it is ideal that the facade blends with the color of the walls. Choose only light shades.

Taking into account simple recommendations, you can adjust the space of even small rooms. By correctly choosing the size, color and depth of the cabinets, you will create the best straight kitchen in your apartment (house).

Corner

The corner module of the original design is quite complicated (item 1 in the figure), not entirely convenient and not very hygienic: along the gap between the back and the seat, dust and crumbs will fall just where it is difficult to remove them. Since in our case the entire corner is made at the place of constant use, it would be more expedient to build a hanging corner for it, tightly fastened to the sofas. Drawings of its 5 parts - seat, support bar and 3 back segments - are given in Fig. The bevel of the corner seat with sofa seats 400 mm wide is 210 mm, and this is considered a half-window window that fits in a small-sized kitchen. The bevel can be straight, convex or concave. The most convenient thing is a slightly convex bevel, but then it will not be possible to attach a bench to arrange a sleeping place. The backrest has an upward camber, which further improves ergonomics.

Drawings of details of the corner section of the kitchen corner

The dimensions of the back segments must be verified according to the location. reasons. First, small parts are greatly affected by the thickness of the skin. Since the sofas were covered earlier, this value will be known by the time the corner section is manufactured. Secondly, all the dimensional errors accumulated in the sofas will converge into one in the corner.

And yet, the seat and backrest segments need to be trimmed freely, without tension, so that the backrest does not overtighten the fabric when assembling. The lower edges of the segments need to be beveled inward by 2 mm (at an angle of 10 degrees, this is with a margin). The tops of the segments can be figured (options in positions 4 and 5 in Fig.), as long as the contours converge at the connecting points.

Note: rear support posts do not need to be installed if there are no suitable scraps and the rider weighs less than 100 kg. If they are installed, then they are attached in pairs of confirmations through the face into the edge. The heel of the lower support is sealed with a piece of ABS and just stands on the floor.

Corners in a corner

This corner also has 2 secrets. The first is a nook under the seat. From the point of view of a domestic animal, this is a reliable reserve den at a safe distance from the main house. And from the point of view of the owners, it does not cause them unnecessary trouble.

Second. The middle segment of the backrest does not bear operational loads. If you place it on friction pins instead of self-tapping screws, a hiding place will form in the cavity behind it. You will just need to sew an outward-facing tongue-strap made of durable fabric to the upholstery of the lower edge, and sew up the corner section from the rear with fiberboard. When closing the cache, the tongue is tucked inward so that it is not visible. To open the cache, the tongue needs to be pryed and pulled out with a fork or something like that. Remove the segment by pulling the tongue and the top of the back. This cache is unlikely to hide anything from an experienced burglar or a professional search, but it is quite reliable from an amateur thief or overly curious household members.

Manufacturing process: step-by-step instructions

There are no minor details in the manufacturing process. Every nuance is important, and therefore it is extremely important to adhere to the instructions and recommendations.

If you are planning a long sofa, first cut out the necessary parts:

bottom, plywood is suitable for making this part;
bars for the frame part;
sidewalls made of chipboard, 2 pieces required;
side parts for the long sides of the box - you also need two parts, which can be made from plywood;
back;
sitting

It is very important to take clear measurements so that there are no problems when connecting the structure.
The next stage is assembly. You need to assemble the sofa in a certain order:

The edges cover the ends of the sidewalls, and the bottom is covered with thrust bearings.
Using a screwdriver and self-tapping screws, the frame is assembled, and then the box.
The back is assembled and attached to the sides using dowels. You can strengthen the fastening using metal corners.

If it was planned to make a short sofa, then all actions will be similar. Only the size of the parts changes.

The most economical option is to use particle board or oriented strand board.

After the long and short sofas are ready, they are combined into one structure using a connecting element. Metal corners with the help of dowels attach the seat to the back, and then attach it to the side. The last stage is upholstery, if it is planned, of course.

If upholstery is not planned, then the wood can be treated with primer and varnish. To change the color, you can use tinting or paint.

The old fashioned way

A kitchen corner made of wood looks chic in any setting, whether it is made from solid wood or boards from unusable construction pallets - pallets, see fig. And making a wooden kitchen corner with your own hands may not be more difficult or more expensive than the one described above.

Kitchen corners made of wood

To start carpentry on wood, and not on viscous and fragile chipboard, it is not necessary to immediately buy an expensive triad of a jointing machine - a manual milling machine - a sander. You can get by with traditional hand (and non-volatile!) hand tools. Processing small parts in piece production with it often turns out to be easier and faster than readjusting the machine for the next operation.

To begin with, in addition to a jigsaw (we are not pedants, this tool is not very expensive, is often needed and is better than a bow saw in all respects), you will need a regular carpenter's plane, a hand jointer and a set of wood rasps. At first, one so-called will be enough. cabinet rasp, flat-convex with a tapered end, on the right in the figure:

Woodworking tools

You will also need selected (emphasis on the “s”) straight and beveled chisel planes (on the left in the figure). Using a straight chisel, remove the folds and select grooves along the fibers, and with an oblique blade across and plan the ends.

For primary processing of knotty wood, you need a sherhebel plane in the center. The sherhebel is used with a slight sliding to the side, as if cutting off and trimming knots. You can turn an ordinary plane into a sherhebel by placing a “piece of iron” knife with a rounded blade in it.

Having gained a little skill, it will be possible to replenish the tool park with another 3-4 types of selected planes with replaceable pieces of iron for them, see next. rice. Take a closer look at antique furniture: it was made with just such a tool, and not with modern machines with shaped cutters.

Selected planers for figure planing

The last point is the assembly (pulling together) of furniture panels from boards, they are also an array of furniture. In theory, this requires special devices - clamps - 3 per tabletop, 4 per cabinet sides and 2 per smaller panels. Here, firstly, one clamp can be replaced with a pair of jaws with clips for mounting on a rod, and a piece of timber of suitable thickness for the clips will go onto the rod, see figure; usually 60 mm. Sets of jaws for clamps and long clamps are sold separately.

Tension clamp made from a pair of jaws with clips and a piece of timber

Finally, wide panels are not needed for the kitchen corner; Most often, a shield for 3-4 boards is required. In this case, a shield from boards can be assembled without any special equipment at all, see video:

Interesting solutions in interior design

At first glance, it may seem that the kitchen corner is a fairly standard version of kitchen furniture and there is no room for creativity. However, designers have repeatedly proven the opposite. A kitchen corner can become a real highlight of the interior if you use your imagination and use a non-standard approach to design.

You can experiment with the shape of the structure, the mechanism, the color of the upholstery and the material from which the furniture is made. You can also think of interesting solutions in terms of the functionality of such an element of furniture in the kitchen.

If desired, you can attach legs or wheels to the corner, then it will be convenient to move it away during cleaning. The option without legs is also good, since debris will not get clogged under the corner; here the choice is individual.

Materials used

The kitchen places special demands on the quality of furniture. There is high humidity and splashes of fat during cooking. Therefore, you need to consciously approach the choice of materials.

Frame

There are no special requirements for the frame material. It is better, of course, to use natural wood, which will increase the service life of the product, but will also significantly increase its cost. Budget options use bars and plywood. Decorative parts can be made of chipboard. You can match these elements to the color of the kitchen set to complete the composition.

The legs and back should be more durable; bars measuring 60x60 mm are suitable for them. It is better to use moisture-resistant plywood with a thickness of at least 12 mm. Angles and screws are used to assemble the frame. The only requirement for them is increased strength, since the finished product is subjected to constant loads.

Upholstery

It is very unpleasant if, after a fish dinner, the sofa exudes the corresponding aroma for a long time, so the upholstery material should not absorb moisture and odors. Besides the smell, another enemy of the kitchen sofa is grease. The upholstery material should be easy to wash and not be afraid of cleaning agents. The upholstery should be made of dense material so that it does not tear or deform during use.

Artificial materials meet these requirements. For additional protection, you can sew a cover that is always easy to remove and wash. And changing the cover is easier and cheaper than restoring a sofa and reupholstering it. Leather also meets the necessary requirements. Such a sofa looks noble and elegant, however, it will cost more.

Budget upholstery options:

cotton is a natural dense material;
flock is a practical, durable material that does not require special care, animal hair does not stick to it, and holes from their claws are invisible on it;
jacquard - dense material, wear-resistant, does not fade in the sun;
velor is an inexpensive, beautiful fabric, but it wears out quickly, easily absorbs moisture, dirt and grease, and loses its appearance due to frequent cleaning;
artificial leather does not fade, is easy to clean and is not afraid of sunlight.

Luxury materials:

microfiber is a very durable material with Teflon impregnation, due to which water is repelled, the fabric is resistant to abrasion and contamination;
tapestry is a natural fabric that is highly wear-resistant;
chenille - the threads of this material are fluffy, which creates a special texture; the fabric does not require complex care;
genuine leather is an expensive material, but it will last a long time, does not require special care, but you should not rub it too much, otherwise the area may become lighter.

Filling

Many materials are used as filling: padding polyester, foam rubber, batting, holofiber, felt. We select the thickness of the material based on the requirements for softness. A semi-hard sofa has a filler thickness of 5 cm, so if you want something softer, you should do more. If the requirements for the rigidity of the sofa in the family differ, you can make the thickness of the filling minimal and additionally sew pillows.

Basic rules for creating furniture yourself

How to install a kitchen unit with your own hands

Before you figure out how to make a kitchen corner with your own hands, you need to clarify the basic nuances of furniture assembly:

The accuracy of the work directly affects the functionality of the products, and the final result depends on many factors.
At the design stage of a kitchen corner, individual tastes and preferences of people are taken into account.
If ready-made circuits are used for manufacturing, then you will have to work with the specified materials. Otherwise, backlashes and gaps will appear in the structure. Strict adherence to the assembly order will be required, as well as the selection of high-quality fittings.
If you have no experience in creating furniture, you should give preference to the simplest, linear models of kitchen corners with laconic decor.
When selecting suitable kitchen corner drawings, you must be guided by the available tools. Thus, making a wooden model is not complete without a grinding machine or jigsaw.

To ensure high-quality assembly, you should think in advance about the appearance of the kitchen corner and determine the place where it will be located. This information will help you choose the most suitable materials and accessories.

Assembly

We restore the kitchen set with our own hands

Before starting assembly, you must inspect and unpack the boxes in which the corner is supplied. On one of the side surfaces of each package there must be a designation of its number. Boxes with the same numbers contain parts of the same type.

Inside one of the boxes there should be a diagram showing the order of assembling the corner. This paper also contains a description of the list of components of the structure. It is necessary to ensure that the parts available correspond to the identical names indicated in the diagram. If you do not have any spare parts, you should contact the furniture supplier or purchase them at a specialized store.

Grouping the component parts of the corner will help to facilitate the assembly process. Parts belonging to the same part of the structure should be placed together.

Next, the main elements are assembled. They can serve as side walls, front and rear walls. Compared to other parts, these parts are the largest. Thus, a bunch of parts making up the main supporting structure is performed.

The parts are connected to each other using Eurobolts

When screwing them in, you should be careful and control the tightening force. An overtightened bolt head can damage the outer decorative coating.

It is important to align the bolt holes in the parts with each other. This is necessary for proper assembly of the structure.

After the main dimensional parts, additional components are mounted. They can be upholstery elements, armrests, shelves, drawers and others.

Technological marks must be placed on the surface of the parts to determine the location of certain fasteners

It is important to ensure that the bolts and screws match their seating points. To ensure the best quality in this regard, it is necessary to periodically consult the instructions

The final touch to completing the assembly is tightening all connections to prevent any backlash.

Factors influencing furniture placement

When choosing a set and arranging its elements and household appliances, the size of the kitchen itself is of great importance. The layout mainly depends on this. However, in addition to the dimensions of the room, it is necessary to take into account:

location of communications, windows, doors, kitchen layout features;

Location of communications in the kitchen

number of household members;
the time usually devoted to cooking;
physiological characteristics of those who will be engaged in cooking (height, weight, etc.);
the nature of the use of the premises (only for preparing meals or as a dining room);
walk-through room or not.

When choosing a headset, a number of factors are taken into account

It involves proper placement of food preparation (stove), storage (refrigerator) and cleanliness (sink) areas, which allows you to provide comfortable conditions for those who prepare the dishes. Ideally, the distance between the main points in the kitchen should be within 1.2...2.7 m.

DIY corner sofa for the kitchen

The standard set of furniture for arranging a dining area includes a table, a corner sofa and stools.

According to the step-by-step instructions, to make a corner sofa for the kitchen, you will need:

Board made of birch, beech or pine 2 by 4 cm - 100 cm.
Beam with a section of 4 by 4 cm, about 135 cm.
The beam is 2.5 by 2.4 cm, about 365 cm.
Beam 1.5 by 1.5 cm thick - 300 cm. For covering the back wall, a sheet of fiberboard.
Plywood 0.8 - 1 cm thick for the bottom and sides.
You also need 5 cm thick foam rubber or padding polyester.
Upholstery fabric (microfiber, tapestry, leather, nubuck and others).

To make a corner sofa for the kitchen with your own hands, prepare:

jigsaw
carpenter's corner
plane
furniture stapler
screwdriver
Sander
drill
bit
hacksaw
pliers
roulette
hammer

You will also need: confirmations, screws 0.4 by 2 cm, 0.4 by 6 cm and 0.4 by 8 cm, bolts and 0.8 cm washers, dowels, legs, hinges. If you plan to make a folding sofa with your own hands, then according to the instructions, you need a special mechanism. The drawing of the sofa for the kitchen should indicate the calculated dimensions and dimensions. In this case, your kitchen corner will fit perfectly into the dimensions of the room.

The workpieces are sanded and leveled, and only then can they be marked and sawed. The average length of a corner sofa is 120 by 90 cm, the corner insert is 45 by 45 cm, and the back height is 85.5 cm.

First, according to the drawings, the main parts of the sofa from the kitchen corner are made - these are the sides. They are made from a thick sheet of plywood. The markings are made with a pencil, and then the part of the kitchen corner sofa is cut out along the lines with a jigsaw.

The next step is to make two frames from 4 by 4 centimeter beams for both sides of the sofa. Both frames should be in the form of parallelepipeds, which are then fixed to the sidewalls. The connections at the corners should look like a mustache and a spike, which are subsequently glued. The T and L shape connections should be at a 90 degree angle.

At the corners, the connections can be with through holes or hidden, go into half of the beam, and also have one, two, or three tenons. They are secured with dowels or corners with self-tapping screws.

The frame of the corner sofa for the kitchen is connected to the back and secured on the sides. When the base is ready, you can assemble the hinged seat covers. Seats can be solid or sectional.

How to make a wooden shelf with your own hands read more

Rectangular frames for seats are made from a block 2.5 by 2.5 centimeters thick. Then they are sewn up with centimeter plywood. The seats are cleaned and covered with a layer of stain and varnish. Then foam rubber is glued and the fabric is stuffed.

A piano loop is attached to the long part of the corner sofa seats. Fastening the hinged covers is done at the end of the work. The corner module is assembled in the same way. A frame is made from a 4 by 4 centimeter block. The profile should be triangular in shape and have sides at angles of 45 and 90 degrees. The module is covered with plywood.

The assembled two parts of the sofas and the corner module are sanded. Exposed wooden elements are covered with stain and, accordingly, three layers of varnish on top. All parts are placed on the sofa legs and fastened together. The connection takes place using screws to the frame support. There must be at least 8 legs.

Structural details are adjusted when adjusting the height of the legs. Marks are made in the places of future fastening. Holes for bolts with a diameter of 0.8 centimeters are drilled. Bolts and washers for them should have wide margins. There should be twice as many washers as there are bolts, so that one goes under the bolt and the other goes under the nut.

The upholstery fabric depends on the proximity of the sofa to the stove and sink. The surface should be easy to clean and not exposed to chemicals.

For a small-sized sofa, 5 cm foam rubber is suitable. For a semi-soft corner of a larger size, padding is taken from padding polyester. Foam rubber or padding polyester is glued to the back with glue. The fabric is cut out according to patterns and stapled to the back of the back, as well as at the junction of the back with the seat. The material is stretched and securely fastened at the corners. Then it is fixed around the entire perimeter.

Sofa restoration

After removing the old upholstery and disassembling the structure, you can begin the repair itself. The extent of work to restore the sofa will depend on the complexity of the damage; below we will look at the most common of them.

Frame repair

You will need to prepare the following materials and tools:

wooden blocks (to replace damaged ones);
plywood sheets;
metal dowels;
wood glue;
vice;
nails.

Step one: replace damaged frame elements with new wooden blocks

Replacing old unusable bars

Step two: take a wooden frame using the same tenon and groove principle, using glue. It is better to further strengthen the structure with the help of metal caps.

Use of metal chokes

Step three: for the base of the spring block, you can take sheets of plywood 150 centimeters wide and about 200 centimeters long. Next, you need to cut out two rectangles according to the dimensions of the structure, then place them on the frame (pre-coat them with glue). Then the plywood should be carefully nailed

Plywood for base

Repair and fastening of the spring block

To work you need to prepare the following:

U-shaped brackets (you can buy them at a hardware store or make them yourself from wire);
nylon banners;
strong thread;
awl;
hammer;
felt or any durable fabric.

Brackets for fixing springs

Step one: we fix the springs using metal brackets with sharp ends, after which they need to be driven in with a hammer. An ordinary stapler cannot cope with such a process.

Fixing the springs

Step two: the springs must be additionally secured with nylon constrictions. You can use a thick rope, which is secured using the same brackets

Nylon thread for attaching springs

Step three: felt should be placed as the top layer. If you don't have one, you can even use old carpet. For greater density, it is advisable to take a double layer of material and then cut it to size. It is fixed using the same dense thread, and holes are made with an awl or a nail. A distance of 35 millimeters is maintained between stitches.

Holes can be made with an awl

Step four: a layer of foam rubber is laid next, and then padding polyester. Along the entire perimeter, the materials are fixed with glue and then hammered in with nails.

Main part

The main part of the process involves several steps. To know exactly how to properly upholster a sofa, you should do everything step by step and carefully.

Repair of internal parts

Repair

You should start by repairing the frame, namely the spring block:

faulty elements are carefully unscrewed with pliers;
install new springs;
insert the block back and secure it with nails.

It is possible to make old springs more elastic using pieces of foam rubber or an old blanket. We stuff the springs with pieces of cut foam rubber. If an old blanket was chosen, then they cover the entire block from above and stitch it with a needle and twine. To ensure that the foam sheets lie tightly, they are first coated with glue. To make the foam look more voluminous, you can lay a padding polyester on top of the foam.

Sewing covers

Regardless of whether the sofa will be upholstered with leather or fabric, the procedure is very simple:

on the floor, with the wrong side up, we lay out the fabric, on which we lay out the elements of the old upholstery on top;
we fix it with needles so that the elements do not move;
We outline all the components with chalk, not forgetting the seam allowances;
cut out the material;
We sew everything together on a sewing machine.

We cover the sofa elements

Fix with a stapler

When everything is ready, the sofa is directly upholstered, or rather its individual components:

we put sewn covers on the back, seats and armrests;
the places where the new covers will be fixed must be exactly where the old covers were placed;
We fix the new covers using a stapler, and the material must be tensioned each time we drive in subsequent fasteners.

for matching marks;
the lock is secured first to the back, then to the seat and drawer;
install the sidewalls and then the armrests;
at the end we fix the wooden panels, having previously varnished them, if necessary.

Procedure for changing upholstery

Benefits of using and creating a kitchen corner with your own hands

Kitchen corners are multifunctional. Tables are needed for family meals, sofas can function as sleeping places. Soft corners are often equipped with spacious pull-out cabinets designed for storing kitchen utensils.

Kitchen corners are a very popular solution in kitchen interior design. They are widespread precisely due to a number of their properties and advantages.

Compactness

By installing such a design, you can significantly save space, which is undoubtedly important for small rooms that combine a kitchen and a dining room. Functionality. The corner can not only serve as a soft, comfortable sofa, but also be equipped with special drawers for storing various things, products and kitchen utensils. Convenience

Thanks to this design, the whole family and house guests can sit at the table. Variety of choice. Designs vary in style, shape and finishing material. You can choose any one to suit your taste. Price. A DIY kitchen corner will cost much less than a ready-made version from a store.

Pay attention to the frame of the kitchen corner. It is advisable to choose materials that are durable and environmentally friendly.