Kitchen cabinet sizes; what are the standard sizes

What is the height of the kitchen countertop from the floor?

The standard height of the working surface is 90 cm from the floor. It is designed for heights from 158 to 172 cm. If everything is correct, then the distance from the bent elbow to the table surface does not exceed 15 cm - then it will be convenient to work. Your hands won't get tired.

Interesting materials:

What are the semi-finished products? What benefits are there for children under 18? What child benefits are there in 2022? What types of fire hoses are there? What are prebiotics? What types of spinning plants are there? What instruments are there for measuring temperature? What are the professions of a manager? What programs are there for interior design? What processor manufacturers are there?

Basic recommendations

If you don't know how much the countertop protrudes in the kitchen, use the following rules:

• In most cases, the width of the tabletop is about 60 centimeters. This is quite enough to comfortably carry out various cooking-related procedures;
• The working surface should protrude above the cabinets in the front by approximately 3-5 cm. In this case, the drawers located below will be reliably protected from splashes;
• It is desirable that the overhang of the kitchen countertop at the back be 5 cm. The thing is that this gap will contain the necessary communications (pipes, electrical wiring, etc.).

How to hang cabinets on a mounting rail?

1. Preparatory work. The wall must be perfectly flat. The installation of slats should be carried out only after making sure that the plasterboard profiles fit snugly to the base.

2. Fixing the tire for mounting. After measurements and markings, we place the tire at the required height and fix them with self-tapping screws. The length of the screws should be selected according to the thickness of the cladding plus 1.5 - 2 cm for fixing to the base wall. To achieve a perfectly even arrangement of the modules, installers advise using a second rail at the bottom edge of the headset items.

3. Installation of fastening fittings to the modules. Typically, the hanging system is connected according to the “rail to runner” principle. The slats are hung on the wall. We screw another tire to the back wall of the cabinet. Instructions for this type of slats can be found in the video on the Internet.

4. Attaching cabinets and shelves to the bar. The cabinet must be assembled without moving elements. Shelves and doors are attached to a suspended and securely fastened module.

The price of fastening rails is higher than traditional fittings.

Mounting to drywall

If you plan to hang heavy-duty kitchen cabinets on a drywall wall, you will need to install reinforced wall cladding. Usually the number of vertical guides is increased. You shouldn’t skimp on the quality of metal profiles either; they must be strong, rigid and reliable. It's also worth shelling out for high-quality metal fittings.

1. Before hanging the cabinet, take measurements using a level. Zero deviations allow the load to be evenly distributed.

2. Do not tighten the bolts too much. Bolts screwed with excessive force can deform the cladding.

3. Lighter wall cabinets can be mounted with hinges and bolts screwed directly into the base. Hanging heavy products involves the use of long self-tapping screws, which are screwed through the thickness of the profile into the base wall.

4. A filled kitchen cabinet weighing more than 20 kg can only be supported by long anchor bolts. Before using the anchor, you should cut a small hole, drill the base wall, and secure the dowel. Then screw in the furniture anchor. When the installation of fasteners is completed, it is worth covering the mounting window with a piece of drywall and carefully strengthening it with mortar.

5. After installation is complete, do not rush to fill the cabinets right away. Double-check the accuracy of angles and slopes with a level

Place the ball. If it does not roll, then the hitch is done correctly. Feel free to fill your cabinets with your favorite things. If an error is found, professional help will be required. Poorly installed wall furniture poses a threat to the safety of household members and property.

Our services

If you are interested in kitchen countertops in Yekaterinburg, give us a call. Keep in mind that you can install such products yourself only if you thoroughly know the technology and have the appropriate tools. Otherwise, you may make many mistakes that will subsequently be impossible to correct. That is why we strongly recommend that our clients cooperate only with professionals!

Most often they do it flush, but for some it makes sense to make the countertop protruding above the cabinets: in the kitchen you have to work a lot while standing and if the cabinets are the same as the table. at one level there is nowhere for the feet to go (just like in the bathroom, when the side is made strictly vertical), which will entail the need to tilt the body (additional load).

Besides. . If the drawers are slightly pulled out when working (for example, with spoons.. knives), then crumbs or debris may accidentally get there when cutting food, which will not happen if the cabinet recedes a little deeper into the countertop.

Hello dear friends.

Today we will talk about the depth of kitchen unit modules.

What can it be in the case of top and bottom?

So, first, let's decide where this size comes from?

And it “dances” (in the case of lower modules) depending on the size of the tabletop.

As you probably know, the width of a standard countertop is 600 millimeters. So, relative to this size, the dimensions of the upper and lower boxes are calculated.

Depth of lower boxes

The bottom of the kitchen is planned so that the countertop protrudes beyond the frame along the front and rear edges.

There should be a protrusion along the front edge, since the facades (which are 16-18 millimeters thick) are still attached to the frame. There should be a small “canopy” of the countertop above the facades, so that if water gets on it, it does not fall on the facades, but runs off it (by the way, for these purposes, some countertops have a so-called “drip pan”).

So, the tabletop should protrude beyond the box along the front edge by 40-50 millimeters.

But, often, the specific indentation is determined by the built-in technology.

For example, when designing lower boxes for some models of dishwashers (which have certain tolerances for installation depth), this indentation has to be made 30 millimeters in size so that this equipment can be built into the box.

Along the rear edge, indentations are also made to accommodate all kinds of communications and other things in the resulting niche. Its size, on average, can be 90-100 millimeters.

In such cases, the depth of the lower boxes is taken to be 460 mm (for guides measuring 450 mm, plus 10 millimeters of free gap)

This is how it turns out:

• Tabletop width – 600mm
• Table protrusion along the front edge – 40mm
• Overhang along the rear edge – 100mm
• Box depth – 460mm

We check:
40+460+100=600 (mm). Everything fits together.

But this is not an axiom.

For example, for a standard tabletop, the depth of the box can be 510mm. (for possible guides, size 500mm).

Then, the protrusion of the table along the front edge will also be 40mm, and along the rear edge – 50mm.

Also in options with an angular bottom, when one of the kitchen wings is planned to be 420mm deep, then the depth of the lower box is usually planned to be 355mm (for guides measuring 350mm).

Review by Alexander D.

Review by Alexander D. about Enitop company

I'm glad I met your company. Everything is done well, with high quality. I am grateful to the sales manager Alina, the measurer Maxim and the installers. Please encourage me.

Corner tabletop for Alexander

This kitchen surface has a familiar shape and is quite compact in size. At one end the table top ends with a smooth curve. There are holes for mounting the hob and sink. The overhang of the countertop (the distance by which it protrudes above the front of the kitchen cabinets) is 20 mm.

Drawing of a kitchen countertop for Alexander

Stone for countertops

We recommend paying attention to the stone that Alexander chose. This is Vicostone Taj Mahal quartz stone. Its appearance exactly repeats the pattern of natural marble, but at the same time it retains all the unique properties of durable and reliable quartz.

Alexander countertops are made from Vicostone Taj Mahal quartz stone

Details about the order

Popular edge

Alexander asked us to make one of the most popular T-40 edges for the tabletop. It is especially good in combination with a skirting board of a similar size: 40 mm in height.

Skirting for Taj Mahal stone countertops

Skirting board 40×12 R3

The order also included a plinth: it served as an excellent decorative element, creating an aesthetic transition from the plane of the tabletop to the wall. The top of the plinth is slightly rounded - just like the edge of the tabletop.

Kitchen cabinet sizes - what are the standard sizes?

Standard sizes of kitchen cabinets make it possible to pre-design the size and location of the furniture set, taking into account the area and configuration of the room.

When buying or making a kitchen set yourself, you need to focus on the standard sizes of kitchen cabinets. They were developed strictly for a person of average height and dimensions. During their calculation, indicators obtained during rest (storing and placing various utensils) and during movement (getting things from the upper shelves, squatting to the lower shelves, bending, performing various actions in a standing position) were taken into account.

Technical aspects were taken into account, for example, the placement of water pipes, open wiring, etc. It is not possible to take into account absolutely all the points without special knowledge; if some standard parameters are not suitable, they can be slightly adjusted to suit you: increase or decrease. In a small kitchen, hanging kitchen shelves , preserving space and convenience.

Installation nuances

1. Before starting installation, stock up on the necessary tools. For brick walls, a simple drill will do, but if the walls are concrete, then you will need a hammer drill.
2. Do not choose fasteners that are too large to attach.
3. When drilling a hole in the wall, take into account the thickness of the plaster layer. We must not forget that the dowel should be in the brick, and not in the plaster. The size of the hole in the brick must be at least 5 cm so that it can be screwed in freely.
4. Try not to hang cabinets on drywall, as such structures are unreliable.
5. It is not recommended to overload mounted models.

All sizes, both walls and floors, should be considered individually. Repairing kitchen units is not a difficult task, and adjusting the hinges is not difficult; if you cannot entrust the work to professionals, do not be afraid and do the installation yourself. The main thing is to read the article carefully and there will be no problems.

Permissible deviations of furniture facades

The quality of MDF facades must comply with the requirements of regulatory documents: GOST 20400-80 “Furniture production products.
Terms and definitions", GOST 16371-93 "Furniture. General technical conditions", GOST 19917-93 "Furniture for sitting and lying. General technical conditions”, as well as TU 5683-46275274-2007, OST 1327-82 and others. The quality of the appearance of the furniture facade is visually assessed in daylight (without direct sunlight) or uniform artificial light, identical to daylight, at a distance of 50 cm at right angles to the plane of the product, without the use of magnifying optical devices, for an observation period of at least 30 seconds. These quality assessment conditions are “normal”, therefore defects or deviations not detected under them can be considered acceptable.

I. PERMISSIBLE DEVIATIONS FOR MDF FACADES

• “shagreen” protruding on the front surface of the product no more than 0.05 mm;
• hardly noticeable risks under PVC film up to 8 mm;
• microstrips and spots on MDF facades in metallic PVC film, which arise due to the specific properties of the “metalized” film;
• repaired chips, as well as technological holes on the back side of the facade, up to 6 mm in size, and no more than 3 per 0.3 sq.m. surface area with the condition that the seals match the color of the surface;
• manifestations of the structure of the MDF board under the PVC film;
• film texture direction distortion up to 5 mm;
• curvature of the facade - no more than 5 mm per 1 m.p.;

NORMALIZED DEVIATIONS: (noticeable when assessing the appearance of the product under normal conditions)

* On the front surface of the product up to 0.3 m2, no more than three different normalized deviations within the tolerance limits are allowed simultaneously, without spoiling the appearance of the product.

* The /-/ sign means that this parameter is not controlled

NOTES: deviations in film color shades in different orders are possible due to the peculiarities of its production technology. Based on the above: - Massive LLC guarantees that there will be no discrepancies in the details of the order, but a deviation in the color shade of the Order with a sample in the rosary, or in a different shade of the parts in the Order, but a deviation in the color shade of the Order with a sample in the rosary, or in previous orders is possible. — to exclude claims for different shades, from 02/01/15. Massive LLC considers any additional orders individually and carries out everything as agreed. — it is possible to have different shades of cornices lined with textured films, where the width of light and dark stripes on the film is commensurate with or greater than the width of the cornice.

II PERMISSIBLE DEVIATIONS FOR SOLID FACADES

A facade made of natural wood is a complex product that includes components made of solid wood, as well as finished with natural wood veneer. Wood is a natural material, so each type of wood has its own shape, color and structure of wood fibers. Natural wood is characterized by the fact that structure, shape and color are not a constant and repeating value. These parameters are a key characteristic of many furniture components and mean that when processing wood it is impossible to achieve uniformity of all indicators and you can always find places where the structure and direction of the fibers differ from each other, where the color changes its shade slightly, depending on the density of either other piece of wood. It must be remembered that in the manufacture of facades many operations, especially in finishing (painting), are performed manually. The combination of all these factors ultimately makes wood products so “alive,” natural and beautiful.

Normalized deviations

Standard sizes

When designing kitchen furniture, it is necessary to follow certain rules and maintain certain distances and dimensions:

• The working surface (tabletop) should be at a distance of 850 mm from the floor. The height was not invented casually, but in accordance with the average height of a European woman and based on working conditions while standing.
• Standard tabletop depth is 600mm.
• The distance from the tabletop to the bottom edge of the upper wall cabinets is ideally 600mm
• The depth of wall cabinets should be 300mm.
• The height of the base of the lower cabinets is 100mm. – This makes it possible to adjust the height of the legs within 10cm.
• The tabletop canopy over the facades is 30mm.

How to install a kitchen if a gas pipe is in the way (heating pipes are in the way)?

Gas pipes are not as scary as they seem. 1) Most pipes can be left as is by making cuts in the furniture.

2) In the gap between the upper and lower cabinets, you can close the pipe with a “box” made of chipboard or wall panel.

3) If the gas pipe extends to the stove along the wall and in the future will be located behind the refrigerator or oven, it is worth spending 4-7 thousand rubles. (for 2013-2014, the cost is determined by Lengaz gas workers) and shorten it. It is also possible for it to be digested higher or lower. It is highly advisable to consult with a kitchen surveyor to determine the most convenient location for a new pipe and valve:

4) If the lower bend of the gas pipe interferes with the installation of the refrigerator, order a “podium” with a height of 20-30 cm for it along with the kitchen. This way the refrigerator will stand close to the pipe, and you can store something on the podium.

5) In rare cases, the drain pipe riser runs through the kitchen. Although this may not directly concern the furniture, you may have in mind this way of decorating it. Just use your imagination:

How to install a kitchen if the walls are very thin?

After all, you want to hang full-fledged cabinets and load them with dishes. 1) you can make a mortgage, for example a beam or board during renovation, at the level of the “top” of the future kitchen.

2) if the kitchen is planned with a wall panel (apron), then it can be made from a 27mm countertop. This way the upper modules will “stand” on it, and the load will be removed from the wall.

3) You can destroy everything and build these thin walls anew - from brick or foam concrete.

How to install a kitchen on drywall?

This finishing material is very fragile, and hanging cabinets loaded with dishes are heavy.

1) When installing, use only special nylon dowels for gypsum board. It’s good if the end of the self-tapping screw also hits the solid base of the wall (concrete, brick).

Technically, it will be easier to hang a kitchen on such dowels if it is on adjustable “carbines” (“Euro hangers”), which in turn cling to the mounting rail.

Mistress's height

The question of how far the kitchen countertop should protrude is extremely important, but we should also not forget about the height of the stone structure. For a long time it was believed that in this case it is best to stop at around 85 cm. This standard was popular in the 50s of the last century.

Practice has shown that in our time such norms are no longer relevant. And all because the height of the average woman has increased. A height of 85 cm will be comfortable only for housewives with a height of 165 cm. If you are taller, then fatigue cannot be avoided during long-term work (the spine receives a strong load).

Try a simple experiment. Bend your arm at a 90° angle. Measure down 15 centimeters. It is at this height that the ideal working surface for you should be.