How to install rollers on a wardrobe door photo

The sliding system is widely used in the creation of modern cabinet furniture. For comfortable operation, various components are used, including rollers for sliding wardrobes - this is a special fitting to ensure the sliding of the panels along the guides. The sliding mechanism allows you to open and close the doors without extra effort and eliminates the occurrence of extraneous noise. The quality characteristics and service life of the entire system depend on the technical properties and correct installation of the roller wheels.

Guide rollers for sliding wardrobes: selection and installation

For people who are just thinking about purchasing a comfortable sliding wardrobe, it can be difficult to understand its design.
First of all, the question arises about the selection and installation of sliding sliding systems, which can be very different. The photo shows the main elements of such systems - rollers for wardrobe doors. As a rule, they come with any cabinet and can be top or bottom. Doors on rollers for sliding wardrobes are the most popular design option today, and therefore it is worth considering in detail what such a system is and dwelling on the important points of its installation. Guide installation process

If you want to assemble a sliding wardrobe yourself, it is even more important to delve into the study of its systems. Installing casters on a wardrobe will not be a very difficult task for you if you approach the issue wisely. And photo and video instructions will become your assistants in this matter.

Mounting options

To install the rollers, you need to decide on the method of their fastening.
To do this, it is necessary to properly fix the guides, since they guarantee simplicity, ease and high quality of opening and closing the doors of the structure. The main elements of the system are the rails, since the sash moves directly along them in a horizontal position. The system additionally includes the following elements:

roller bearings;
plugs intended for the profile;
high-quality seals;
reliable fasteners;
other small fittings;
other devices, and their availability depends on the characteristics of the selected videos.

The mounting depends on the type of system chosen. If an upper sliding system is made, then the doors are suspended on a control located at the top of the opening. The rollers roll along this guide. The lower guide in such a system acts only as a latch along which the rollers move. If the installation is done correctly, there will be no vibrations in the blade. The advantages of such a system include the fact that it gives the cabinet an attractive appearance and also ensures ease of opening the doors.

The lower system has a similar device, but the lower profile acts as a support. The upper rails and rollers are only necessary to ensure that the sashes do not fall out. The combined system involves installing supports at the top and bottom. This option for fastening the sashes is considered the most reliable and high-quality, but installing and adjusting all elements is a complex process.

Thus, fastening can be performed in different ways, which are selected after studying the material of the doors, their weight and other parameters. The choice depends on ease of use and financial capabilities. If you have a cabinet of large size and weight, then it is advisable to focus on installing a combined system.

Rollers for sliding wardrobe doors are mandatory elements if sliding systems are used to open the doors. They can be made from various materials and can also be presented in different types. The safety and comfort of use of all furniture depends on their proper selection and installation.

At the same time, it is important that no extraneous or loud sounds arise during the operation of the structure. If you carefully understand its structure, installation and regulation can be carried out independently

Major breakdowns

Key points that come up when using a wardrobe:

the doors do not fit closely to the cabinet walls, or to each other;
the doors are tight, there are creaks and other extraneous sounds;

The second problem can be solved by cleaning the chute along which the rollers move, which can be clogged with dirt and dust. You can clean it with a sharp object or a vacuum cleaner.

Perhaps your problem can be solved by cleaning the guides.

But the first problem is more complicated. Doors may not fit for various reasons:

if there is a gap in the middle between the door and the walls of the cabinet, then this may indicate that the cabinet is overloaded;
cracks can also arise due to problems with the frame itself, which can be tilted in one direction or another;
if the door opens without permission or there is a gap between the wall and the door, this may indicate a malfunction of the stopper or its absence, in this case you need to install the stopper in place and, if possible, fix it with glue or a small screw.

Mounting options

Before installing the rollers, it is necessary to properly secure the guides; the ease of sliding of the sash along the rails depends on this. The method of fastening depends on the type of mechanism chosen. For an overhead sliding system, guide rails are fixed at the top of the doorway.

In this case, the lower guide serves only as a latch along which the rollers move. With proper installation, the door leaf does not vibrate or wobble, and the doors open easily and effortlessly.

The lower fastening is considered the most reliable, but it is very difficult to do it yourself without the help of professionals. It is necessary not only to correctly install the guides and the lower roller for the wardrobe, but also to adjust all the elements together. The upper rollers in this case serve to keep the sashes in place and not fall out.

Installation of guides

At the top of the doors, the guide profile must be built in so that it does not protrude above the side walls. But you can’t leave a gap between the profile and the wall; you need the same length as the width of the cabinet.

Since the door leaves are located on the lower profile, they need to be secured with self-tapping screws in increments of 25-35 cm. They need to be screwed alternately into different channels.

The top profile is attached first

Before installing the bottom guide you need to:

Secure the top profile
Put it in place without securing the bottom profile
Install 1 door leaf

This way you can determine how much and where you need to move the bottom guide. After the profile is set, you can remove the sash and secure the guide with self-tapping screws.

The lower profile is attached to self-tapping screws only after adjusting the sash

This option is much simpler than the first. First, thoroughly clean the surface on which the tape will be glued from dirt, dust, grease and possible burrs. We clean it carefully so as not to accidentally erase the marks that were made with a pencil. We expose the sticky side of the tape and apply the guide to the floor in exact accordance with the markings. We press the element along its entire length for a while.

Before installing doors in a wardrobe, or more precisely when choosing a method for installing the lower guide element, you need to remember an important nuance. If you need to preserve the coating, that is, you don’t want to drill holes in it, you can use tape, but there is only one attempt at gluing it, since it will be impossible to tear the good material off the surface. Be extremely careful and attentive, and do not make mistakes when marking.

Materials for manufacturing accessories

DIY wardrobe door installation

The mechanism consists of bearings and rollers. Aluminum and steel are used to make bearings. Reliable and attractive aluminum systems ensure silent gliding of the rollers. Steel structures are stronger and more durable, but more expensive than aluminum ones.

The wheels themselves are made from various materials:

Plastic. Inexpensive accessories, but you must use them carefully, otherwise they will quickly break. These models do not take shock load well and wear out quickly. During use, chips and dents appear on them.
Rubber. Soft products that do not create noise, but their service life is not very long. Such fittings wear out quickly and need to be replaced.
Steel. Durable fittings are made with special soft linings for silent sliding. They hold a very impressive load, so they can be installed on large cabinets.
Tarmonide. A composite material that hardens as it cools.
Teflon. Has optimal technical parameters for a long service life. Steel rollers are coated with Teflon so that they move silently along the guides.

Varieties

The videos are presented in several types, each of which has its own purpose and rules of use:

upper roller - designed to implement a supporting function throughout the entire system. Its correct installation ensures that the door leaf is secured vertically. For a sliding wardrobe, a mechanism is selected that includes not only the rollers themselves, but also rubberized wheels. Rubber is intended to reduce the noise that occurs during the movement of the doors, and also ensures that there is no knocking if the doors swing or significant force is applied to close them. The upper rollers can be spring loaded. They differ in size and structure, and the choice depends on what type of vertical profile is used in the furniture. If there is an open profile, then an asymmetrical roller is installed, and if the profile is closed, then only the symmetrical option is suitable;
lower rollers - perform a supporting function. They are the ones that are affected by the main load coming from the cabinet door. The mechanism is equipped with a special pressed-in bearing, and its presence guarantees a long service life of the product, as well as high quality construction. An additional shock-absorbing spring is certainly used, thanks to which the sash moves softly and smoothly. The installation of this type of roller must be carried out with special care, since the correct adjustment of the position of the doors relative to the walls of the furniture depends on this. This is especially true if the floor in the room has numerous uneven surfaces.

To install cabinet doors, a different number of rollers can be used; if the weight of the leaf does not exceed 60 kg, then you can use two rollers, and if the weight is more than this indicator, then it is advisable to use 4 pairs. Types of casters further vary depending on the installation method, as certain varieties are mounted into aluminum frames installed along the door, while others are simply installed inside the cabinet.

Features and advantages of fittings

A roller mechanism is a special type of cabinet fittings that ensures smooth sliding of the door leaf along the runners when closing and opening the doors. Its presence guarantees:

soft, silent movement of door leaves;
opening or closing doors without effort;
the impossibility of spontaneous displacement of facades to the side, even if drafts appear in the house;
ensuring the vertical position of the canvases;
space saving - the rollers move horizontally, they do not need free space under the cabinet;
the possibility of using auxiliary devices, including remote control devices;
attractive appearance of a piece of furniture.