How to assemble a phoenix sliding wardrobe with your own hands: instructions

How to assemble a wardrobe?

Assembling the Basya sliding wardrobe does not present any difficulties for a person who knows how to use tools.
Such furniture can be placed not only in the bedroom, but also in the country house or in the hallway; everywhere this furniture will look completely relaxed and organic. Instructions for assembling the wardrobe are included with each unit of product, but difficulties still arise from time to time in its layout, especially in the question of how to assemble a wardrobe for a beginner. In addition to the manual, it is recommended to watch the video materials on the website, which show in detail how to assemble the Basya wardrobe.

The “Basya” cabinet is assembled as follows:

First, the frame is installed. All cabinet components are marked and numbered, so it will be easy to work. Assembly begins from the bottom corner. The side wall is connected to the bottom using self-tapping screws, and another wall is installed in parallel nearby. Before doing this, it is better to look at the photo in the instructions. After the frame is assembled, the back wall comes into play, which is attached with small nails to the assembled base. Also, instead of nails, 3 mm screws are often used. The product should be assembled from top to bottom, the wall is fixed on both sides, it gives rigidity and stability to the entire structure

construction square;
good meter level;
roulette;
plumb line

The assembled frame is prepared, which means it’s time to attach the back panel; it is attached both from the outside and from the inside. After completing this assembly phase, it is recommended to test how smoothly all the elements are fastened, and if something is done incorrectly, this will negatively affect the operation of the product, and the service life will be noticeably reduced.

After the frame is installed, the installation of the shelves begins. They are fixed with the help of special cylindrical wooden blocks, which are called chopiks. Moment glue, screws, and dowels are also actively used. It should be noted that all markings are on standard parts, so the process of installing blocks does not present any difficulty. The most important step is the door layout

How to attach a mirror, it is recommended to look at the assembly diagram of the Basya sliding wardrobe with a mirror. After the assemblers have completed the main work, the fittings can be installed.

As you can see, the description is quite accessible even for a primary school student. You can determine the correct installation of the Basya wardrobe by some characteristic features:

the product rests on the floor, without any distortions;
there are no gaps at the joints;
the door opens and closes silently without any effort.

Having made sure that everything is fine, the “Basya” cabinet can be safely used, loading it with contents.

Assembly steps

To know where to start, it’s worth familiarizing yourself with its stages. Most sliding wardrobes are assembled according to the following algorithm:

base;
frame;
installation of the rear wall;
installation of shelves and guides;
installation of compartment doors.

After the completed stages, the implementation of internal additional elements is carried out. These include pull-out baskets, drawers, rods, hanging hooks and pantographs. Let's consider the installation of each cabinet element separately.

Base

The assembly of sliding wardrobes, the video of which is presented below, begins from the bottom part, which bears the entire load during operation. We find a part that will perform this function and place it in front of us. In order for the process to proceed correctly, we use tools such as screwdrivers or a screwdriver, a hexagon, a pencil and a tape measure for marking. Also check the package for the presence of self-tapping screws and special masking plugs.

The algorithm of actions looks like this:

on the part for the bottom, the place for installing the base is marked;
sometimes, instead of base strips, adjustable legs are used, the place for which also needs to be marked;
drill holes for fasteners;
we attach the bottom to the slats using confirmata (corners) - for this we use self-tapping screws and a screwdriver;
We assemble the transverse supports of the plinth, designed for stability.

Some products, such as the Phoenix coupe model, require installation using adjustable legs. This is easy to do: the plastic plugs are cut off with a knife, and the legs themselves are screwed into holes prepared at the bottom with a diameter of 10 mm.

Depending on the size of the assembled wardrobe, the number of legs will be adjusted. So, for large planes more than 6 support elements will be required.

Frame

Before disassembling and assembling sliding wardrobes from scratch, it is important to familiarize yourself with the general structure of the existing product. Study the diagram carefully, because assembling the housing must ensure safe operation of the cabinet. The stability of the internal elements will depend on how securely it is installed.

In order for the furniture assembly to be accurate, you should additionally check the floor surface for evenness. Use a building level: if there are differences on the floor, tighten the adjustable legs. Only after this assemble the product box.

To ensure quality installation of the housing, follow these steps:

It is better to assemble the product while standing, because it is very difficult to install a perfectly fitted cabinet in a lying position. But it is important to remember that for complete assembly it is necessary to leave at least 100 mm for the installation of the roof;
in the part that is responsible for the bottom, you must first drill several holes and insert anchors. Rack strips will be mounted on the installed fasteners;
Installation of stand-up panels is carried out by two people: in order not to get confused, you can view the instructions for assembling the sliding wardrobe presented in the video. The left side panel is inserted first, one person holds it while the second person inserts the right side panel;
at the next stage, the middle stand is installed, if present. After its installation, the roof is installed. If the cabinet is assembled in a standing position, then this part will be properly secured to the corners or confirmations.

How to work with laminated chipboard - a popular material for cabinet furniture

How to assemble a wardrobe with your own hands
Currently, laminated chipboard is mainly used in the production of furniture. This is the first principle. It is wood shavings of coarse dispersion. Using the hot pressing method, it is given the shape of a sheet. In the manufacture of slabs, formaldehyde resins are used; they are an additional component. The difference from simple chipboard is the coating with a film made of paper and melamine resin. In terms of environmental indicators, it is better to use materials of class E1. Laminated chipboard boards have good compaction, due to which furniture made from them is strong and has a long service life.

Fastening the rails to the cabinet door

If you think that this material has the same composition, then you are mistaken. Based on their coating, they are divided into veneered, rough and laminated. Based on their quality composition, they can be divided into three grades: first, they use first-class sawdust (usually wood of the same species). The surface is flawless, not a single chip. The plate is decorated, laminated with film or veneer. Second grade – you can already see small defects. There may or may not be cladding. Third, there are already noticeable defects here. Such slabs are not covered with anything.

Until the cabinet is fully assembled, make sure that the attached parts do not tilt, as the fasteners may break off.

In addition, laminated chipboards are moisture-resistant and fire-resistant (withstand high temperatures). They are mainly used to make furniture frames, but are also used in the production of partitions or used as interior decoration. It is worth mentioning that laminated chipboard, due to its composition, perfectly holds nails and screws.

In order to give rigidity to the wardrobe, it is necessary to secure the back wall.

The main “steps” for assembling sliding wardrobes with your own hands are indicated in the instructions.

Furniture made from these boards has many advantages compared to other materials.

Acceptable price indicators.
No difficulties in manufacturing.
Good quality.
Significant period of use.
Variety of colors and decorations. This will help you choose the perfect furniture for your living room, kitchen or children's room.
Blends perfectly with other materials.

Such furniture looks great in any interior.

Another important feature of laminated chipboard is that these boards have heat and sound insulation. Therefore, they can sheathe the walls of the room.

Make sure that the holes for the shelves and hanger rod mounts match the holes on the opposite rack.

Also, if you have started remodeling an apartment/house, knowing how to assemble a wardrobe yourself will help you easily and quickly resolve the issue of moving this furniture.

Required Tools

DIY three-door wardrobe

Almost every cabinet model comes complete with the necessary bolts, nails and washers, but you need to prepare the tools yourself. To assemble the wardrobe, you will need the following tools:

Phillips screwdriver.
Bit PZ2.
The screwdriver is straight.
Screwdriver or drill.
4 mm drill bit for metal.
Hammer.
Level.
Pliers.
Stationery knife.
Hex key.

You may also need additional parts to assemble a 3-door wardrobe. For example, if the floors are uneven, it is necessary to prepare the underlays in advance. Depending on the model, a confirmat and 6 mm drill may be required.

What tools are needed

Significant expenses in purchasing the tool will not be required. To assemble a kitchen set, a wardrobe or a hallway, you need to have the usual set of tools: a screwdriver, a hex key for confirmation, a screwdriver, various drills, a bat for confirmation, an awl, a pencil, a tape measure, a square, fine-grained sandpaper, an electric drill, a stationery knife, iron, joint knife, rubber mallet, clamp for parts.

The distance between opposite corners should be the same.

Assembling a wardrobe with your own hands is quite easy and anyone can do it simply by following the instructions.

It is unrealistic to guess what tools will be needed to assemble furniture. It depends on what kind of project it is - difficult or not.

Now you need to install the wardrobe doors.

To open a closet, you don't need to remove chairs or move other furniture.

Installation of additional materials

We make a wardrobe ourselves from design to assembly with our own hands

Usually shelves are fastened with corners and self-tapping screws. Manufacturers pre-drill holes for hardware on these parts. All that remains is to measure and determine the optimal distance between the shelves and screw them to the side and central strips.

During assembly, never tighten fasteners until all parts are in the correct position.

The hanger bar is mounted on the flanges that come with it. If necessary, the pipe can be shortened using a hacksaw.

Work very carefully and hold the elements constantly.

To install drawers, you must first attach the mechanisms to the rack strips

It is very important to install them parallel to each other at the same height. Then there will be no problems with retractable mechanisms

The fiberboard boards are fixed with wood screws. Screw them in carefully; the screws should land exactly in the middle of the furniture boards.

Cabinet assembly rules

Experience and practical skills in assembling structures such as a cabinet certainly play an important role. However, even with minimal skills, it is possible to get the job done.

To do this, you need to follow a number of specific aspects on how to properly assemble a cabinet:

Before starting work, you should carefully read the instructions for assembling the cabinet.
Prepare the necessary tools and clean the area for installing the cabinet.
Carefully lay out all the parts on the floor or table and count them. The lack of just one element can disrupt the entire assembly process.
Carry out the work gradually; haste in this case is not the best help.
If you encounter any difficulties, you can watch several video tutorials on assembling the cabinet.

All mirrors and glass panels are assembled last, so as not to scratch or break them during the work.

General rules for assembling cabinet furniture

To assemble purchased furniture, you must follow the cabinet assembly instructions provided by the manufacturer. There are certain rules. By following them, you will assemble any item with high quality and in a short time.

You shouldn’t take everything out of the packages at once, much less mix parts from different packs. Maintain the order.
Read the instructions carefully so that later there are no overlaps and you don’t have to redo it again.
Make sure the fittings and components are in place. Otherwise, you will not be able to completely assemble the furniture. The handles must match the color scheme. It is necessary that the drawer guides have a soft movement.
Assemble one section at a time in order. You need to start from the bottom, gradually moving to the sides.
Open the package, lay out the parts, prepare the tools.
Mirrors and glass are installed at the final stage. This way you will avoid damage.

For assembly you need a screwdriver, a screwdriver, a hex key, and a tape measure.

If you do the manufacturing yourself, it will be much easier to assemble.

It is very important to follow the assembly sequence, otherwise you will be forced to disassemble and reassemble the cabinet in the correct sequence.

Preparing all materials for assembly

You need to prepare in advance the tools that may be needed. Usually the minimum required is: keys, screwdriver or screwdriver, hammer (rubber and regular), pencil, ruler, tape measure. It is also advisable to use a building level to check how level the cabinet is assembled relative to the floor.

You need to assemble the cabinet on the floor. It is optimal to do this in such a position that lifting a heavy body after assembly requires a minimum of effort and energy.

Advice. Parts should not be immediately removed from their packaging. After inspection, it is better to put them in boxes so as not to accidentally damage them.

Wardrobe assembly instructions

Our procedure for assembling the wardrobe will be as follows.

You need to start assembling from the bottom of the cabinet, namely by assembling the base and installing the legs.

We take a part called the bottom and mark its lower side for installing the base and legs as shown in the diagram below:

The plinth can be secured to the bottom using mini fixes (eccentrics, rasteks - whoever calls them), confirmats or ordinary plastic corners.

Since this will still be an invisible area, and the cabinet will not stand on a plinth, but on legs, I decided to secure the plinth using plastic corners. The legs were secured with 3.5*30 screws.

Just when you screw the legs, don’t overdo it (you can over-tighten it, and the sharp part of the screw will come out from the back side).

We attach the four parts of the base to each other using confirmations. For convenience, take yourself a corner clamp. You can use it.

We will attach the sides to the bottom and roof with minifixes. They are great for fastening perpendicular parts, and they also manage to completely hide the fastener.

If space allows, it is convenient to assemble the sliding wardrobe lying on the front part and fasten it using confirmations. But since I didn’t have any free space in my room, I had to assemble it standing up and use eccentrics (rastexes, minifixes) as fasteners.

On the bottom and roof of the cabinet (from the inside) we mark holes for installing the minifix rod.

Before installing the sides, using a level, the bottom of the wardrobe must be leveled as evenly as possible. Simply lean the level and adjust the legs to the maximum horizontal position.

Now you need to mark the sidewalls, the holes should exactly coincide with the installed rods on the bottom and roof. In the sidewalls you will need to do two different drillings in two different planes.

The first hole is made for a metal eccentric, which will tighten the rod, it is made in the inner side of the sidewall, with a special 15mm cutter, at a distance from the edge of the end to the center of 34mm (this is if the rod has a total length of 44mm, like mine).

In general, when fitting a part onto a rod, its head should protrude 6 mm. If this is your first time installing minifixes, practice better on rough parts, so you will feel more confident when assembling.

The second hole is made at the end of the part, with a 6-6.5 mm drill, strictly in the center (8 mm from the edge).

For a more detailed understanding of this assembly step, you can use our materials on.

When you have made all the necessary holes, do not rush to install the sides and roof right away.
To give the structure initial rigidity, immediately assemble the central partition with the upper shelf (we fasten it with confirmations).
At the next stage, we need to place the sidewalls, the rear wall of the console and the assembled T-shaped partition on the lower rods, tighten them with eccentrics, and secure the upper shelf to the sidewalls (with confirms). Use an angle clamp for support.
Next, we attach the roof and check the verticality using a level.
If everything is fine, to provide additional rigidity, we install additional shelves using confirmats.
Now, using 3.5*16 screws, we fasten the back wall of the fiberboard. We start from the two upper corners, and after perfect alignment, we begin to screw in screws throughout the box, in increments of 15-20mm. The fiberboard should also be secured to the central partition and the top shelf.

The hardest part of the job is finished. We put the cabinet in its place, once again check the position of the cabinet by level and proceed to installing shelves, hangers and drawers.

To have fewer plugs for holes on the visible side of the wardrobe, I decided to install the shelves on shelf holders.

Everything is simple here. We mark the required height on the sidewall, use a 4.5-5 mm drill to make a non-through hole, up to 8 mm deep, and hammer the shelf holder into it.

A sliding wardrobe is one of the most convenient and compact ways to store things. It has small shelves for light items of clothing, and large ones for bulkier items, there are compartments for storing skis, a compartment equipped with a rod for placing outerwear, etc.

The compactness of the closet is made possible by sliding doors, which do not require space to swing open; they move on special rollers located inside the structure of the door itself. Even a person inexperienced in such matters can assemble such a cabinet, since the assembly principle is quite simple and does not require the use of special tools.

Step-by-step assembly diagram for Phoenix sliding wardrobes

There is a slight difference between the Phoenix and Metrolux productions, which does not affect the assembly methods, but it is worth knowing about them.

First step. Checking and unpacking

When purchasing furniture, you took measurements, check them. If the furniture will be installed across the entire width of the room, during assembly, leave a distance between the wall of the furniture and the room. This is a common mistake in most factory production. The fiberboard wall is secured with self-tapping screws on the back side. Once secured, you will not be able to exit the cabinet unless you leave gaps. It needs to be deployed. To do this, you need to take into account the diagonal of the furniture and, using the Pythagorean theorem, add some reserves.

Second step. Unpack the parts and make room for assembly

The diagram offered in the kit is usually incomprehensible and primitive, which is only suitable for a temporary backing for the fittings while you are assembling the cabinet. Therefore, you immediately need to pay attention to the internal content. Find the model you need on the Internet and take a look at it.

Third step. Determining how shelves, drawers and hanging racks will be located

Often these two parts are interchangeable, which allows you to install shelves on both the left and right sides for the convenience of the owner. To determine, you need to measure the width of the shelf and the distance of the holes at the bottom.

Important! For proper installation, the width of the shelf must be at least 1 cm greater than the distance between the holes.

Fourth step. Installing adjustable legs

We disconnect the plugs (do not throw them away, they will come in handy). Afterwards, we insert them into the lower part of the body, there are special holes there, the diameter of which is 11 cm. How many legs there will be depends on the dimensions.

If we talk about “Megalux” furniture, the holes for the legs are made independently and you need to take into account that there should be 70 mm in front from the edge to the center, and 50 mm behind. In Phoenix furniture everything is much simpler.

Fifth step. We attach minifixes to the upper and lower parts of the body

We turn the parts over and screw the pins into a previously prepared hole with a diameter of 0.4 cm.

Sixth step. Installing side and interior walls

You can't do this without outside help. An assistant will hold the chipboard, and you, at this time, install the side wall on a pre-screwed pin, then secure the shelves with confirmation. The sides have holes, you just need to use a wrench and tighten them.

Next we install the next side panel. If the furniture is large, you may need to install all the internal vertical boards at once.

Important! Do not use electrical appliances here. Factory furniture, especially cheap ones, can be easily damaged.

Seventh step. Upper part of the structure

If the closet is not wide, you can do it yourself, but it is better to ask for help. We fix the minifix eccentrics into a special hole in the upper and lower parts, its diameter is 1.6 cm. And we twist it, assembling the frame. At the end we get a box, unstable, but already similar to a cabinet. Often, the furniture manufacturer does not provide plugs in the kit in order to save money. But to close the connection, they can be purchased separately.

Eighth step. Back wall

We take measurements of the diagonals, taking into account that the walls of standard models are made of chipboard with a thickness of 1.6 cm. Sometimes the sidewall can be slightly concave or curved, which will not allow us to make perfect diagonals. This can be eliminated by using bumpers, but if the diagonal is close to ideal, this is not necessary.

Important! We nail the back part from bottom to top. This way you make sure that the edges of the material do not extend beyond the sides.

Choose the distance for the nails yourself. There are few of them included with the fittings, but a large number of small nails will increase the reliability of fastening.

Assembly order

The base (bottom sheet of laminated chipboard) is screwed with euroscrews (confirmats) to two longitudinal legs made of laminated chipboard. The supporting part must have an edge so that the material does not swell from moisture while standing on the floor. You can immediately nail the thrust bearings - 3 pieces per strip.

The work takes place on the floor and therefore the box is assembled face down.

You need to attach the middle post to the base of the Basya cabinet and then the side ones, and in order not to return to the bottom again, put plugs in the holes of the Euroscrews. Don't forget to install heel supports on the side racks of the cabinet.

The next step is to tighten the top lid of the cabinet and install the plugs. To give rigidity to the box, install shelves that are tightened with Euroscrews between the sections (in some configurations such shelves are not available).

We measure the diagonal and nail the back wall

Before nailing the back wall, make sure that the wardrobe is rectangular in shape. This is done with a square, placing it on the corner of the cabinet, or using a tape measure to measure the diagonals. You can use two options at once to make it more accurate. All angles should be equal to 90º, and the diagonal of the two sides should be the same. In case of unevenness, it is necessary to level the housing by moving it to a smaller direction.

If the box has the exact shape and details, then you can nail the back wall of the cabinet. The reinforcement wall is attached not only around the perimeter, but also to the shelves.

Now the structure should be rigid and can be installed in a vertical position.

Installation and configuration of doors

Two running rollers are screwed to the top of each door. It happens that mirrors come attached to the middle door of Basya's closet, but if the manufacturer did not glue it, then you will have to do it. To do this, you need to attach a mirror and outline it in a circle. Then plant it on liquid nails.

Now you need to install the lower guides and upper rails for the rollers. Stepping back 2 cm from the edge, screw the guide at the bottom and the rail at the top in the same way.

Then carefully insert the doors into the grooves of the profile. The motion of the rollers should be soft, and the doors should fit well and not touch or cling to anything. In case of poor running, the rollers can be adjusted. After this, screw the rollers with a fixing screw. We screw the guides onto the lower parts of the doors. Now we install the top front strip and install shelves and a rod for dresses. The Basya cabinet is ready for use.

Main assembly steps

The wardrobe is assembled strictly according to the diagram, vertically or horizontally. The second option is better, this way you can prevent skewing of the parts being connected. If the height of the ceilings does not allow you to raise the finished cabinet, then it is better to carry out the work in a vertical position.

You can easily assemble a sliding wardrobe with your own hands if you follow the step-by-step instructions.

In such a closet you will place twice as much clothes without the expense of the enormity of the furniture itself.

The first step is to attach the base and adjustable legs to the bottom. They are necessary if the floor is uneven. Next, we begin assembling the body. We connect the sides to the base. To make the structure durable, we attach an intermediate rack and a shelf. This is necessary so that the sidewalls do not tilt. Then we screw the remaining parts and attach the lid. It is advisable not to nail the back wall, but to screw it with self-tapping screws. At this stage we put the cabinet in its place. We install guides for drawers, holders for shelves, and a bar for hangers. Check that the drawers should slide out smoothly.

You need to familiarize yourself with all the details of the product (so as not to confuse anything during the assembly process and not have to start all over again), prepare the tools and the place where the assembly and installation will take place.

This work will take a lot of your time.

Next up is door installation. First we attach the guides, then we fix the rail with screws. We insert the doors, check that they open and close smoothly. Adjust them if necessary. Lastly, glue on the sealing brushes. We attach plugs to the confirmation holes.

Do not warp the cabinet parts, keep the corners straight.

To summarize, we can say that assembling a wardrobe is not such a difficult job. Your desire, skill and ability will allow you to do this without difficulty.

After you do everything, be sure to check how the doors work (do they creak, move freely, etc.), how securely the shelves and other parts are fastened.

Be careful that until the cabinet body is assembled and the back wall is installed, all fasteners can be easily broken.

How to work with laminated chipboard - a popular material for cabinet furniture

Currently, laminated chipboard is mainly used in the production of furniture. This is the first principle. It is wood shavings of coarse dispersion. Using the hot pressing method, it is given the shape of a sheet. In the manufacture of slabs, formaldehyde resins are used; they are an additional component. The difference from simple chipboard is the coating with a film made of paper and melamine resin. In terms of environmental indicators, it is better to use materials of class E1. Laminated chipboard boards have good compaction, due to which furniture made from them is strong and has a long service life.

Fastening the rails to the cabinet door

Until the cabinet is fully assembled, make sure that the attached parts do not tilt, as the fasteners may break off.

In order to give rigidity to the wardrobe, it is necessary to secure the back wall.

The main “steps” for assembling sliding wardrobes with your own hands are indicated in the instructions.

Furniture made from these boards has many advantages compared to other materials.

Acceptable price indicators.
No difficulties in manufacturing.
Good quality.
Significant period of use.
Variety of colors and decorations. This will help you choose the perfect furniture for your living room, kitchen or children's room.
Blends perfectly with other materials.

Such furniture looks great in any interior.

Another important feature of laminated chipboard is that these boards have heat and sound insulation. Therefore, they can sheathe the walls of the room.

Make sure that the holes for the shelves and hanger rod mounts match the holes on the opposite rack.

Also, if you have started remodeling an apartment/house, knowing how to assemble a wardrobe yourself will help you easily and quickly resolve the issue of moving this furniture.

Installation of side walls and top cover

Attach the sides to the bottom and roof using confirmations or eccentric ties, depending on the drillings made. If there are no mounting holes, it is permissible to assemble the housing using mounting angles - this eliminates the need for additional marking and drilling.

Expert opinion Alexander Didenko Furniture assembler at Mabax

You should not immediately tighten the fasteners as much as possible, since vertical partitions and shelves will still need to be installed in the future.

Pay attention to the method of mounting the top cover. It can be mounted from above: in this case, if the distance to the ceiling is insufficient, you will not be able to tighten the bolts.

When installing the top cover in our case, the help of a second person was required

Otherwise, the side walls risked folding.

Sliding wardrobe Phoenix - width 1.7 m, 2 facade colors to choose from

Delivery in Moscow and Moscow Region:

Delivery is carried out to the entrance.

Delivery cost in Moscow and Moscow Region:

Delivery is carried out to the entrance.

Delivery in Moscow

FOR FREE

All prices do not include delivery costs outside the Moscow Ring Road

Delivery cost outside the Moscow Ring Road

cost per 1 km. from MKAD

Assembly in Moscow and the Moscow region:

The pickers' departure occurs both upon delivery of the order and can take up to 3 business days after complete delivery. The specific date of assembly is agreed by the Buyer with the Seller by calling the assembly department.
To assemble the furniture, the Buyer or his adult representative must be present at the address.
The opening of packages is carried out by the assembler in the presence of the Buyer or by the Buyer during self-assembly.
The assemblers assemble only the furniture assortment specified in the invoice.
In cases of unfinished self-assembly by the Buyer, factory assemblers will travel to complete the work for a fee of 15% of the cost of the furniture. In this case, no warranty is provided for the furniture.
Furniture is assembled strictly according to the design (assembly diagram), changes to the design, furniture dimensions during the work at the request of the Buyer are made under his responsibility and are paid for separately. If the sold furniture does not fit into the dimensions of the room, then refurbishment of furniture by assemblers to new sizes (if possible) is carried out at the expense of the Buyer.

Sliding wardrobe "Maestro": step-by-step assembly instructions

How to assemble a sliding wardrobe can be read in the “Instructions for assembling a sliding wardrobe”, which is included in the package. However, there are some details that require strict adherence. A sliding wardrobe is furniture that performs many functions; now such models have become very widespread.

Cabinet Features

Sliding wardrobe "Maestro"

Assembling the Maestro sliding wardrobe takes a little time and is not particularly difficult. Installing such a product for an adult man who has a little knowledge of the instrument is a matter of one or two hours. It is recommended to watch the video instructions first.

Parameters in millimeters:

width 170 cm;
height 222 cm;
60 cm deep.

Maestro cabinet parameters

Inside, the shelves are arranged functionally and thoughtfully. There are also mezzanine shelves. Cabinets are produced covered with a pleasant soft color (wenge or ash). The front of the cabinet can be Loreto or oak. White doors create an image of imposingness and sophistication. There are large format mirrors with special bevel processing.

Inside view of the cabinet

Sliding wardrobe Phoenix (Wenge/Oak Milk)

Color:

Description
Characteristics
Reviews
Delivery

The sliding wardrobe "PHOENIX" is made of 16 mm thick laminated chipboard in the following colors:

Wenge/bleached oak
Ash shimo dark/ash shimo light

Behind the side doors of the compartment there is a bar with a shelf

The central section with hinged doors is equipped with shelves for clothes

buy the “PHOENIX” sliding wardrobe right now by placing an order on the website or through our managers.

The cost of delivery in St. Petersburg, excluding lifting goods to the floor, is 800 rubles. Delivery at a certain time with an interval of 1 (one) hour is paid at a double rate.
Red zone Green zone Yellow zone
The cost of delivery to the suburbs, excluding lifting goods to the floor - from 900 rubles * * The cost depends on the distance of the locality from the city limits.

Please check with the manager by phone for the exact cost of delivery to a specific location.

The cost of delivery in a assembled car is 1500 RUR

The cost of delivery to Vyborg by separate car is 4800 RUR

Please check with the manager by phone for the exact cost of delivery to a specific location.

Goods from a warehouse in Moscow are delivered by courier. Not the entire catalog is presented at the Moscow warehouse; please check availability with managers by phone or email.

Installation of internal partitions

After complete assembly of the external part, we proceed to the internal part, namely the installation of partitions. We place them strictly according to the instructions with the side we need in the places already marked by the manufacturer; if, by mistake of the manufacturer, there are no such places, then we use the size information on the instructions and drill them ourselves. Move the partitions into their places, fasten them using eccentrics or wooden dowels; these fastenings will already be in the cabinet kits. After that, we tightly tighten the fasteners of the outer case, and at this stage you can lift it vertically into its place if it was in a lying state.

Do not forget that in individual wardrobe models, the assembly of the side frame and partitions must occur simultaneously.

Preparation before assembly

First you need to prepare the room. The final outcome of the case depends on this, how much time you spend on work. The important point is that nothing interferes. Make sure all materials and necessary tools are at hand.

As a depth limiter, you can use a 6 or 8 plastic dowel mounted on a drill.

With the help of a wardrobe, you will visually separate different zones in the room, for example, a working area from a relaxation area.

Assembling furniture at first glance seems simple. Many people make mistakes, resulting in defects: the doors and sashes do not fit together well, the doors can creak when opening, misalignment of the holes causes misalignment of parts, furniture does not stand securely on the floor. To avoid this, you must adhere to certain rules and instructions.

Built-in wardrobes of various models, made from natural and artificial materials, are very popular in interior design.

Some models of wardrobes can be transformed to suit the features of the room: the presence of a corridor, recesses in the wall where the wardrobe can be placed.

Assembling a sliding wardrobe: video and stages of work

When you have all the ready-made parts for your future wardrobe, watch the training video again and you can get ready for assembly.

At the preparatory stage we will need an iron

. The edge must be attached to the end of the part so that the more attractive side is at the top. Now run a hot iron along the edge, making sure the steam setting is turned off.

After the edge has warmed up, it needs to be pressed and wiped well, treating the cut edges with sandpaper. Take your time, because quality work is the key to a beautiful cabinet.

Be sure to think about the base. From its parts, assemble the base of the podium for the lower part of the structure. In the video you can clearly see in what order what needs to be done.

Assembly steps

Before work, prepare the following:

roulette;
drill;
drills 5 and 8 mm;
rectangle;
pencil.

The work of assembling a wardrobe with your own hands consists of the following stages:

So, the assembly work is completed

, and we successfully assembled and installed a homemade wardrobe with our own hands. Of course, this is quite difficult; you may need to watch the video several times and re-read a lot of manuals on this matter. And if you did it once, then the second time will be much easier.

Cabinet fittings
Installation of shelves and doors
Installing a mirror and sliding door
Making drawers

In the hallway, living room, and bedroom you need to use comfortable and roomy furniture that does not take up much space. The best option in this case would be, especially since it is quite easy and fast. To assemble such a structure, it is best, after drawing up the drawing, to order elements for it from a specialized factory. They will be made quickly and efficiently, and this will also save time on assembly and on the materials themselves. If you start preparing parts at home, you need to ensure the availability of complex tools and a processing machine, and this is not always possible. Therefore, it is better to take your own measurements at home, draw up a drawing indicating the obtained values, and then contact the factory to order the necessary elements. To draw up a drawing, you can use special programs. An example of a drawing with dimensions is shown in the figure. IMAGE 1.

A DIY sliding wardrobe can become not only a convenient storage space, but also a decoration for the room.

Assembling a sliding wardrobe “Phoenix” with your own hands

Self-installation has several disadvantages - the length of the process, low quality due to lack of knowledge.

Is it difficult to assemble furniture yourself? As practice shows, doing this is not as difficult as it seems at first glance. There have been cases when women assembled simple structures without outside help. Of course, this rarely happens, but it shows that anyone can assemble factory furniture, even without special skills.

To assemble furniture yourself, you will need some tools and time. Depending on the dimensions, specialists spend about three hours on assembly. Expect to spend a little more time on this.

What will you need for work? Among the most necessary tools it is worth highlighting:

confirmation key;
Phillips and flat screwdriver;
a screwdriver (if you don’t have one, a drill will do) with a 0.4 cm drill bit for metal;
centimeter;
awl and building level.

a confirmed drill and a regular 0.6 cm drill;
If the floor has uneven surfaces, it is better to use underlays.

How to work with laminated chipboard - a popular material for cabinet furniture

Fastening the rails to the cabinet door

Until the cabinet is fully assembled, make sure that the attached parts do not tilt, as the fasteners may break off.

In order to give rigidity to the wardrobe, it is necessary to secure the back wall.

The main “steps” for assembling sliding wardrobes with your own hands are indicated in the instructions.

Furniture made from these boards has many advantages compared to other materials.

Acceptable price indicators.
No difficulties in manufacturing.
Good quality.
Significant period of use.
Variety of colors and decorations. This will help you choose the perfect furniture for your living room, kitchen or children's room.
Blends perfectly with other materials.

Such furniture looks great in any interior.

Another important feature of laminated chipboard is that these boards have heat and sound insulation. Therefore, they can sheathe the walls of the room.

Make sure that the holes for the shelves and hanger rod mounts match the holes on the opposite rack.

Also, if you have started remodeling an apartment/house, knowing how to assemble a wardrobe yourself will help you easily and quickly resolve the issue of moving this furniture.

Sliding wardrobe "Phoenix" (Interior Center) in Novosibirsk

The product "Phoenix" sliding wardrobe (Interior Center), manufactured by the "Interior Center" factory, combines high quality, comfort and a favorable price. It will fit perfectly into any interior, and will also create a functional environment in your home and will serve you for many years. The manufacturer provides a guarantee for all materials used in production.

You can order the offered product (art. M04168) for only 15,470 rubles in our online store. You can choose another option from the “Sliding wardrobes” category on the website or by calling +7 (383) 207-95-61. Our specialists will tell you in detail about the terms of order, delivery and payment.

In our store you will find attractive prices, high quality, direct deliveries from the manufacturer and fast delivery in Novosibirsk and other cities. We wish you pleasant shopping!

You can order furniture delivery or pick up the order from the warehouse yourself.

Delivery in Novosibirsk and Novosibirsk region

The cost of furniture delivery in Novosibirsk and the region depends on the distance (see table).

Delivery cost, rub.

Dzerzhinsky, Oktyabrsky, Kalininsky, Zaeltsovsky, Central, Zheleznodorozhny, Leninsky, Kirovsky, Klyuch-Kamyshenskoye

Pervomaisky, Tulinsky, March 8, Krasnoobsk, p. Mochische, quarry Mochische, Pashino, Razdolnoye, Marusino, Novolugovoe, Kamenka, Blizky

Sovetsky, Baryshevo, Pavino, Verkh-Tula, Krupskoy, ObGES, Berdsk, Koltsovo, Krivodanovka, Novy, Kudryashovsky, Tolmachevo, Ob, Nizhnyaya Eltsovka, Akademgorodok

Outside Novosibirsk, up to 50 km from the city

from 1200 to 1800 (check with managers)

Outside Novosibirsk, more than 50 km from the city

20 rub. per 1 km (mileage in both directions is considered)

Please check with the operators by phone for the cost of delivery to locations not listed in the table.

IMPORTANT! 1. Delivery is carried out to the entrance/gate. Lifting to the floor or apartment is a separate service and is paid additionally. Ask your operator for details when placing your order.

2. Delivery occurs on working days. You can agree on the delivery interval (before or after lunch) with the operator.

Pickup

You can pick up your order from the warehouse yourself.

Warehouse address: Novosibirsk, st. Sibiryakov-Guardsmen 62k3.

Opening hours: Mon-Fri from 10:00 to 20:00, Sat, Sun from 12:00 to 15:00.

IMPORTANT! Pickup of goods is carried out ONLY with an advance payment of at least 30% (transferred to a Sberbank card 4279 3806 2269 1667, owner Evgeniy Viktorovich).

1. Assembling furniture requires special skills. We recommend contacting professional assemblers.

Preparatory work

Make room on the floor for ease of use during assembly. There are times when this is not possible, then find an assistant and assemble the wardrobe while standing. Understand the instructions, lay out all the components and arrange the racks, shelves, and other components in order.

The internal parts of the external racks have many holes for shelves and other elements. In order not to confuse them during assembly, marks can be placed on the sides - left and right sides.

To assemble Basya you will need:

hammer,
rubber mallet,
roulette,
metal square,
screwdriver,
screwdriver,
4 mm hex key.

Rear mount

The back wall of cabinets is usually made of HDF with a thickness of 3-4 mm. It is fastened using furniture nails, special branded fixtures or 4*16 screws and backing corners or washers of the appropriate diameter. The second and third options are preferable because they firmly fix the back wall, unlike furniture nails. The pitch length between fastenings is 150-180 mm.

Not all cabinet models have a back wall. In our case, it is missing and we simply place the cabinet close to the wall

Screw the HDF along the entire perimeter of the outer cabinet body, to the internal partitions and rigidly fixed shelves. You can secure the back wall at an earlier stage, immediately after installing the internal partitions, while the body is still lying on the floor. The front decorative side should face inward.

Expert opinion Alexander Didenko Furniture assembler at Mabax

Make sure that the diagonals of the cabinet are equal to each other. The permissible deviation is 5 mm per 1 m. Move the sides if necessary. Once the back wall is screwed in, it will be impossible to level the cabinet.

Sliding wardrobe Phoenix 1500

Facade color

Wenge/Bleached Oak, Dark Shimo Ash/Light Shimo Ash Depth, mm 520 mm Width, mm 1500 mm Height, mm 2100 mm Manufacturer Interior Center, Penza Body material laminated chipboard Facade material Mirror, laminated chipboard Body color

Dark shimo ash,

Wenge Filling of cabinets, chests of drawers, cabinets, pencil cases Laminated chipboard shelf, Rod

Assembly and installation of furniture

Assembly is an additional service for assembling furniture into a finished form.

Installation is an additional service for installing assembled furniture directly to the walls of the room, for example, hanging kitchen units, mezzanines and wall shelves.

Assembly and installation is carried out within 3 working days from the date of delivery of the order.

Tools and materials

Among all types of clothing storage products, the leading place today is occupied by the wardrobe. It is multifunctional, spacious, comes in different shapes and sizes, and does not require additional space to open the doors. That is why most people, when choosing between a wardrobe and a sliding wardrobe, prefer the latter option.

Assembling a sliding wardrobe with your own hands in the video presented is not at all difficult - all you need to do is have the necessary tools in your apartment and be familiar with the design of the product. Often, when ordering a cabinet without the services of assemblers, the company sends a document that contains a drawing of the product. This also lists all the component parts, which are numbered in order. By looking at the drawing and comparing the elements of the cabinet, you can intuitively assemble the product.

To work according to the sliding wardrobe assembly diagram, you will need the following tools:

building level - to check the levelness of the installation parallel to the floor;
corner;
rubber and regular hammer;
straight and Phillips screwdriver;
roulette;
pencil and ruler;
screwdriver;
wood drill - to make holes;
metal drill – for installing an aluminum base.

Additional tools for assembling furniture yourself include a jigsaw, drill and sandpaper. It is also necessary to prepare all the details of the cabinet, which means checking the diagram to ensure that the number of items matches

Pay attention to fittings and mechanisms: if there are drawers in the closet, ball guides should be included

Doors for the product are often supplied ready-made. They are pre-installed with rollers and a strip of soft material. The door must be installed in the final phase.

Tools

Phoenix light sliding wardrobe assembly video - Rating of sites by subject

— Sliding wardrobes to order in Kaluga. Sliding wardrobe in the hallway, sliding wardrobe in the room, sliding wardrobe in the bedroom, sliding wardrobe in the nursery, sliding wardrobe in the library, sliding wardrobe in the office, sliding wardrobe in the living room.

Company People's wardrobe, sliding wardrobes, custom-made furniture - built-in and corner sliding wardrobes. Manufacture and sale of furniture, wardrobes. Large catalogs of wardrobes. Furniture, hallways, wardrobe. All of Russia buys our furniture: sliding wardrobes in Moscow, sliding wardrobes in St. Petersburg.

Google PageRank: 0 out of 10

Information portal about sliding wardrobes in Nizhny Novgorod. Interesting articles and useful information for the consumer. If you are going to buy or order a sliding wardrobe now or in the future, then visit the website

Google PageRank: 0 out of 10 Yandex TIC: 20

Sliding wardrobes, custom-made furniture - built-in and corner wardrobes. Manufacture and sale of furniture, wardrobes. Large catalogs of wardrobes. Furniture, hallways, wardrobes - all this can be bought inexpensively in our online furniture store. All of Russia buys our furniture.

Alexa Rank: #116,946 Google PageRank: 5 out of 10

offers the production of inexpensive custom-made sliding wardrobes according to your sizes in Moscow and the region.

wardrobes, compartments, order, production, inexpensive

Alexa Rank: #9,283,744 Google PageRank: 2 out of 10